Filter
Top Products
9
If the above message
appears, remove, empty
and clean the drip tray.
The drip tray receives waste water and the coffee grounds collector receives used coffee grounds.
The coffee cleaning tray allows you to eliminate any deposits of coffee grounds above the percolation chamber.
Remove, empty and
clean the coffee
grounds collector.
The drip tray is equipped
with floats to tell you
when to empty it.
The warning message will remain displayed if the coffee grounds collector is not slotted in fully or not fitted correctly.
If the coffee grounds collector is fitted within less than 8 seconds, the appliance will ask you to confirm that you have
correctly emptied it. You cannot make espresso or coffee while the warning message is displayed.
The coffee grounds collector has a maximum capacity of 12 coffees.
MAINTAINING YOUR APPLIANCE
As soon as you remove the coffee grounds collector, you will have to empty it completely to avoid any overflow.
Remove the coffee
cleaning tray.
Clean it under water
and dry thoroughly
before re-fitting.
EMPTYING THE COFFEE GROUNDS COLLECTOR, THE COFFEE CLEANING TRAY AND THE DRIP TRAY
RINSING THE COFFEE-MAKING SYSTEM - SEE “BEFORE FIRST USE” SECTION
AUTOMATIC CLEANING PROGRAM – TOTAL DURATION: ABOUT 20 MINUTES
You should perform the cleaning program about every 360 preparations of espresso or coffee.
The appliance will let you know when you need to proceed with cleaning through the ‘clean’ light coming on.
Caution! To benefit from the warranty conditions, it is essential to perform the appliance cleaning cycle
when informed to do so. Be sure to follow the order of operations.
You can continue to use the appliance, but you are advised to perform the program as soon as possible.
To perform the cleaning program, you will need a recipient with minimum capacity of 0.6 litres and a KRUPS (XS 3000) cleaning
tablets.
The automatic cleaning program
is in three parts – the cleaning
cycle itself, then 2 rinsing cycles.
This program lasts about 20
minutes.
Press to perform cleaning
at any time and then choose
MAINTENANCE => OK =>
CLEANING from the menus dis-
played.
Press the key
to start the
automatic cleaning pro-
gram when the
“Cleaning needed”
message is displayed.
Just follow the
instructions
shown on the
screen.
If you press the ‘On/Off’ key during cleaning or in the event of power failure, the cleaning program will start
again right from the beginning. You will not be able to postpone this operation. This is essential due to water
system rinsing reasons. In this case, you will need to use another cleaning tablet. Be sure to complete the entire
cleaning cycle to avoid any risk of irritation (seek medical advice if cleaning solutions are accidently swallowed.
The cleaning cycle is a discontinuous cycle. Do not put your hands under the coffee outlets during the cycle.
Only use KRUPS (XS3000) cleaning tablets. We cannot be held responsible for any damage that may result
from the use of tablets from other brands.
You can obtain cleaning tablets from KRUPS Service Centres.
Make certain to protect your work surface during cleaning cycles, especially if they are made of
marble, stone or wood.
FALCON DISPLAY ANGLAIS 26/10/05 8:56 Page 9
ODRŽAVANJE VAŠEG APARATA
!!!Upozorenje: Kada Vas uređaj upozori da je vrijeme za čišćenje, pridržavajte se uputa da ne biste poništili
jamstvo. Vodite računa da pratite upute za uporabu, korak po korak. Možete nastaviti koristiti Vaš uređaj iako je
žaruljica upaljena, ali preporučujemo čišćenje što je prije moguće.
Čim uklonite spremnik iskorištene kave, morati ćete ga isprazniti do kraja da izbjegnete bilo kakvo prosipanje.
!!! Koristite samo KRUPS (XS3000) tablete za čišćenje. Mi ne odgovaramo za štete ukoliko koristite neke druge
tablete. Tablete za čišćenje možete naći u KRUPS servisu.
Osigurajte da su radne površine zaštićene tijekom procesa čišćenja, naročito ako su od mramora, kamena ili
drveta.
Poruka upozorenja će ostati na zaslonu ako spremnik korištene kave nije ispražnjen, namješten ili ako nije vraćen za 8
sekundi. Aparat će Vas pitati da potvrdite da ste ga ispraznili. Ne možete praviti kavu ili espresso ako je poruka i dalje
prikazana na zaslonu. Spremnik ima kapacitet od maksimalno 12 napravljenih kava.
Ako pritisnete „On/off“ tipku tokom procesa čišćenja ili ako nestane struje, proces čišćenja će početi ponovo.
Nećete biti u mogućnosti odgoditi ovu operaciju. U ovom slučaju, trebati će Vam druga tableta za čišćenje. Nastojte
u potpunosti završiti proces čišćenja da biste izbjegli rizik od iritacije (potražite savjet liječnika ako su preparati za
čišćenje slučajno progutani) Ciklus čišćenja je nastavljajući ciklus. Ne stavljajte ruke pod cjevčice za kavu u tijeku
procesa.
Program čišćenja trebalo bi da pokrenete nakon svakih 350 napravljenih kava. Aparat će Vas obavijestiti da je vrijeme
za čišćenje, jer će se „clean“ lampica upaliti.
Za program čišćenja biti će Vam potrebna posuda minimalnog kapaciteta 0,6l i KRUPS (XS3000) tablete za čišćenje.
PRAŽNJENJE SPREMNIKA ISKORIŠTENE KAVE, SPREMNIKA ZA OTPATKE I POSUDE U KOJU KAPA VODA
AUTOMATSKO ČIŠĆENJE – VRIJEME TRAJANJA: OKO 20 MINUTA
ISPIRANJE DIJELOVA KOJIM KAVA KRUŽI - POGLEDAJTE DIO „PRIJE PRVE UPORABE“
Pritisnite „Prog“ tipku
da započnete proces
automatskog čišćenja,
kada se na zaslonu
pojavi „cleaning needed“
poruka.
Jednostavno
slijedite upute
na zaslonu.
Program automatskog čišćenja je
trodijelni proces. Proces čišćenja
i dva procesa ispiranja. Program
traje oko 20 minuta. Tipkom „Prog“
možete započeti proces čišćenja
bilo kada. Nakon toga odaberite
MAINTENANCE=>OK=>CLEANING
iz menu-i na zaslonu.
Posuda u koju voda kaplje skuplja prljavu vodu i spremnik iskorištene kave skuplja iskorištenu kavu.
Ladica za čišćenje nedozvoljava skupljanje kave iznad komore
8
If the above message
appears, remove, empty
and clean the drip tray.
The drip tray receives waste water and the coffee grounds collector receives used coffee grounds. The coffee cleaning tray
allows you to eliminate any deposits of coffee grounds above the percolation chamber.
Remove, empty and
clean the coffee
grounds collector.
The drip tray is equipped
with floats to tell you
when to empty it.
The warning message will remain displayed if the coffee grounds collector is not slotted in fully or not fitted correctly.
If the coffee grounds collector is fitted within less than 8 seconds, the appliance will ask you to confirm that you have
correctly emptied it. You cannot make espresso or coffee while the warning message is displayed.
The coffee grounds collector has a maximum capacity of 12 coffees.
MAINTAINING YOUR APPLIANCE
As soon as you remove the coffee grounds collector, you will have to empty it completely to avoid any overflow.
Remove the coffee
cleaning tray.
Clean it under water
and dry thoroughly
before re-fitting.
EMPTYING THE COFFEE GROUNDS COLLECTOR, THE COFFEE CLEANING
TRAY AND THE DRIP TRAY
RINSING OUT THE COFFEE CIRCUIT: SEE PAGE 5
MACHINE CLEANING PROGRAM – TOTAL DURATION: ABOUT 20 MINUTES
You should perform the cleaning program about every 350 preparations of espresso or coffee.
The appliance will let you know when you need to proceed with cleaning through the ‘clean’ light coming on.
Caution! To benefit from the guarantee conditions, it is essential to perform the appliance cleaning cycle
when informed to do so. Be sure to follow the order of operations.
You can continue to use the appliance, but you are advised to perform the program as soon as possible.
To perform the cleaning program, you will need a recipient with minimum capacity of 0.6 litres and a KRUPS (XS 3000) cleaning tablet.
Press the
key to start the
automatic cleaning
program when the
“Cleaning needed”
message is dis-
played.
Just follow the
instructions
shown on the
screen.
The automatic cleaning program is in
three parts – the cleaning cycle itself,
then 2 rinsing cycles. This program
lasts about 20 minutes.
Press to perform cleaning at
any time and then choose MAINTE-
NANCE => OK => CLEANING from
the menus displayed.
If you press the ‘On/Off’ key during cleaning or in the event of power failure, the cleaning program will start
again right from the beginning. You will not be able to postpone this operation. This is essential due to water
system rinsing reasons. In this case, you will need to use another cleaning tablet. Be sure to complete the entire
cleaning cycle to avoid any risk of irritation (seek medical advice if cleaning solutions are accidently swallowed).
The cleaning cycle is a continuous cycle and the pump can be heard intermittently. Do not put your hands under
the coffee outlets during the cycle.
Only use KRUPS (XS3000) cleaning tablets. We cannot be held responsible for any damage that may result
from the use of tablets from other brands.
You can obtain cleaning tablets from KRUPS Service Centres.
Make certain to protect your work surface during cleaning cycles, especially if they are made of
marble, stone or wood.
DISPLAY-ANGL(est)25-02:Mise en page 1 27/02/08 12:21 Page 8
8
If the above message
appears, remove, empty
and clean the drip tray.
The drip tray receives waste water and the coffee grounds collector receives used coffee grounds. The coffee cleaning tray
allows you to eliminate any deposits of coffee grounds above the percolation chamber.
Remove, empty and
clean the coffee
grounds collector.
The drip tray is equipped
with floats to tell you
when to empty it.
The warning message will remain displayed if the coffee grounds collector is not slotted in fully or not fitted correctly.
If the coffee grounds collector is fitted within less than 8 seconds, the appliance will ask you to confirm that you have
correctly emptied it. You cannot make espresso or coffee while the warning message is displayed.
The coffee grounds collector has a maximum capacity of 12 coffees.
MAINTAINING YOUR APPLIANCE
As soon as you remove the coffee grounds collector, you will have to empty it completely to avoid any overflow.
Remove the coffee
cleaning tray.
Clean it under water
and dry thoroughly
before re-fitting.
EMPTYING THE COFFEE GROUNDS COLLECTOR, THE COFFEE CLEANING
TRAY AND THE DRIP TRAY
RINSING OUT THE COFFEE CIRCUIT: SEE PAGE 5
MACHINE CLEANING PROGRAM – TOTAL DURATION: ABOUT 20 MINUTES
You should perform the cleaning program about every 350 preparations of espresso or coffee.
The appliance will let you know when you need to proceed with cleaning through the ‘clean’ light coming on.
Caution! To benefit from the guarantee conditions, it is essential to perform the appliance cleaning cycle
when informed to do so. Be sure to follow the order of operations.
You can continue to use the appliance, but you are advised to perform the program as soon as possible.
To perform the cleaning program, you will need a recipient with minimum capacity of 0.6 litres and a KRUPS (XS 3000) cleaning tablet.
Press the
key to start the
automatic cleaning
program when the
“Cleaning needed”
message is dis-
played.
Just follow the
instructions
shown on the
screen.
The automatic cleaning program is in
three parts – the cleaning cycle itself,
then 2 rinsing cycles. This program
lasts about 20 minutes.
Press to perform cleaning at
any time and then choose MAINTE-
NANCE => OK => CLEANING from
the menus displayed.
If you press the ‘On/Off’ key during cleaning or in the event of power failure, the cleaning program will start
again right from the beginning. You will not be able to postpone this operation. This is essential due to water
system rinsing reasons. In this case, you will need to use another cleaning tablet. Be sure to complete the entire
cleaning cycle to avoid any risk of irritation (seek medical advice if cleaning solutions are accidently swallowed).
The cleaning cycle is a continuous cycle and the pump can be heard intermittently. Do not put your hands under
the coffee outlets during the cycle.
Only use KRUPS (XS3000) cleaning tablets. We cannot be held responsible for any damage that may result
from the use of tablets from other brands.
You can obtain cleaning tablets from KRUPS Service Centres.
Make certain to protect your work surface during cleaning cycles, especially if they are made of
marble, stone or wood.
DISPLAY-ANGL(est)25-02:Mise en page 1 27/02/08 12:21 Page 8
8
If the above message
appears, remove, empty
and clean the drip tray.
The drip tray receives waste water and the coffee grounds collector receives used coffee grounds. The coffee cleaning tray
allows you to eliminate any deposits of coffee grounds above the percolation chamber.
Remove, empty and
clean the coffee
grounds collector.
The drip tray is equipped
with floats to tell you
when to empty it.
The warning message will remain displayed if the coffee grounds collector is not slotted in fully or not fitted correctly.
If the coffee grounds collector is fitted within less than 8 seconds, the appliance will ask you to confirm that you have
correctly emptied it. You cannot make espresso or coffee while the warning message is displayed.
The coffee grounds collector has a maximum capacity of 12 coffees.
MAINTAINING YOUR APPLIANCE
As soon as you remove the coffee grounds collector, you will have to empty it completely to avoid any overflow.
Remove the coffee
cleaning tray.
Clean it under water
and dry thoroughly
before re-fitting.
EMPTYING THE COFFEE GROUNDS COLLECTOR, THE COFFEE CLEANING
TRAY AND THE DRIP TRAY
RINSING OUT THE COFFEE CIRCUIT: SEE PAGE 5
MACHINE CLEANING PROGRAM – TOTAL DURATION: ABOUT 20 MINUTES
You should perform the cleaning program about every 350 preparations of espresso or coffee.
The appliance will let you know when you need to proceed with cleaning through the ‘clean’ light coming on.
Caution! To benefit from the guarantee conditions, it is essential to perform the appliance cleaning cycle
when informed to do so. Be sure to follow the order of operations.
You can continue to use the appliance, but you are advised to perform the program as soon as possible.
To perform the cleaning program, you will need a recipient with minimum capacity of 0.6 litres and a KRUPS (XS 3000) cleaning tablet.
Press the
key to start the
automatic cleaning
program when the
“Cleaning needed”
message is dis-
played.
Just follow the
instructions
shown on the
screen.
The automatic cleaning program is in
three parts – the cleaning cycle itself,
then 2 rinsing cycles. This program
lasts about 20 minutes.
Press to perform cleaning at
any time and then choose MAINTE-
NANCE => OK => CLEANING from
the menus displayed.
If you press the ‘On/Off’ key during cleaning or in the event of power failure, the cleaning program will start
again right from the beginning. You will not be able to postpone this operation. This is essential due to water
system rinsing reasons. In this case, you will need to use another cleaning tablet. Be sure to complete the entire
cleaning cycle to avoid any risk of irritation (seek medical advice if cleaning solutions are accidently swallowed).
The cleaning cycle is a continuous cycle and the pump can be heard intermittently. Do not put your hands under
the coffee outlets during the cycle.
Only use KRUPS (XS3000) cleaning tablets. We cannot be held responsible for any damage that may result
from the use of tablets from other brands.
You can obtain cleaning tablets from KRUPS Service Centres.
Make certain to protect your work surface during cleaning cycles, especially if they are made of
marble, stone or wood.
DISPLAY-ANGL(est)25-02:Mise en page 1 27/02/08 12:21 Page 8
Ako se na zaslonu pri-
kaže ova poruka,uklonite,
ispraznite i očistite pos-
udu u koju voda kaplje.
Posuda u koju voda kaplje je
opremljena sa pokazivačima
koji Vam pokazuju kada je
trebate isprazniti.
Uklonite, ispraznite
i očistite spremnik
iskorištene kave.
Isperite ga pod vodom
i osušite pažljivo prije
ponovnog namještanja.
Uklonite spremnik za
otpatke.