Filter
Top Products
13
TROUBLESHOOTING, CORRECTIVE ACTIONS
The appliance fails to come on when you
press the On/Off key.
The espresso or coffee is not hot enough.
The coffee is too weak or not strong
enough.
The coffee flows too slowly.
The coffee is not creamy enough.
You used ground coffee instead of coffee
beans.
The coffee does not come out of the outlet
holes.
The grinder makes a strange noise
The grind setting button of the mill is hard
to turn
Steam does not come out of the nozzle.
Not enough froth on the milk.
The milk froth is too bubbly
The Auto-Cappuccino accessory does not
suck in the milk (accessory sold separately).
You have filled the water tank, but the
warning message remains displayed.
The cleaning program refuses to start.
The scale removal program refuses to start.
You have emptied the coffee grounds
collector, but the warning message remains
displayed.
You have washed the cleaning tray, but the
warning message remains displayed.
A power failure occurred during a cycle.
There is water or coffee under the
appliance.
A “Fault No. XX” message appears.
Check that the power supply cord plug is correctly inserted in the socket.
Heat the cups by rinsing them in hot water
Change the coffee temperature setting.
Check that the coffee bean container contains coffee.
Reduce the volume of coffee selected using the rotating button.
Select the strong coffee key.
Turn the grinding fineness button to the left to obtain a finer grind.
Turn the grinding fineness button to the right to obtain a coarser grind (may
depend on the type of coffee used).
Turn the grinding fineness button to the left to obtain a finer grind(may depend
on the type of coffee used). Ensure coffee beans are fresh.
Use your vacuum cleaner to remove the ground coffee in the coffee bean
container.
The outlet hole is blocked by dry coffee. Use a fine needle to clear the holes.
There are foreign bodies in the grinder
Contact your Krups service centre.
Change the mill setting only when in operation.
First turn off your appliance and let it cool down:
- Clean out the outlet hole with a needle
- Clean out the steam nozzle support pipe with a needle.
Check that the steam really comes out of the nozzle and dry the hole.
Use a recipient and cold milk at the temperature it comes out of the refrigera-
tor. Change the type or brand of milk as appropriate.
Check that the two ends of the small stainless steel tube fit correctly into the
steam nozzle seal.
Check that the tube immersed in the milk is not blocked.
Check for correct joining of the flexible tube with the accessory to avoid any
air leakage.
First turn off your appliance and let it cool before clearing the Auto-
Cappuccino accessory outlet hole.
Check for correct positioning of the tank in the coffee maker.
Check that the float at the bottom of the tank moves freely.
Rinse the accessory and if necessary remove scale.
Disconnect the appliance for a few moments then turn on again.
Disconnect the appliance for a few moments then turn on again.
Remove the collector, make certain that it is empty, wait for 8 seconds and
then fit it again.
Check that the collector is correctly pushed in.
Remove the tray, wait 8 seconds and then fit it again.
Check that the cleaning tray is correctly pushed in.
The appliance will re-initialise automatically when power is turned on and be
ready for a new cycle.
The drip tray is overflowing. Empty and clean the cleaning tray.
Check for correct positioning of the drip tray.
Disconnect the appliance for a few moments then bring it back into service.
If the failure persists, note the fault number and contact the
Krups service centre.
FALCON DISPLAY ANGLAIS 26/10/05 8:56 Page 13
MOGUĆI PROBLEMI I ISPRAVNI POSTUPCI
Uređaj se neće uključiti i kada pritisnete „On/off“ tipku. Provjerite da li je uređaj pravilno uključen u struju.
Espresso ili kava nije dovoljno vrela.
Zagrijte šalice pod vrelom vodom. Promijenite
temperaturu kave.
Kava je preslaba ili nije dovoljno jaka.
Provjerite da li u spremniku za kavu ima kave. Smanjite
jačinu kave rotirajućom tipkom.Izaberite tipku za jaču
kavu. Okrenite polugicu za fino mljevenje prema lijevo.
Kava protiče previše sporo. Namjestite polugicu za fino mljevenje prema desno.
Kava nije dovoljno kremasta.
Namjestite polugicu za fino mljevenje prema lijevo.
Provjerite da je kava u zrnu svježa.
Koristili ste mljevenu umjesto kavu u zrnu. Pomoću usisivača uklonite mljevenu kavu.
Kava ne izlazi iz cjevčica za kavu.
Cjevčice su blokirane suhom kavom. Koristite iglu da
očistite rupice.
Mlinac proizvodi čudan zvuk.
Strano tijelo se nalazi u mlincu. Kontaktirajte Krups
servis.
Kolutić za stupanj mljevenja je teško pokrenuti. Pomičite kolutić prilikom mljevenja.
Para ne izlazi kroz cjevčicu za paru.
Isključite uređaj i pričekajte da se ohladi:Očistite rupicu
iglom.Očistite cjevčicu iglom.
Nema dovoljno pjene u mlijeku.
1. Provjerite da li para izlazi kroz cjevčicu, osušite
rupicu na gornjem dijelu cjevčice.
2. Rabite posudu i hladno mlijeko iz hladnjaka.
3. Rabite svježe mlijeko.
4. Promijenite proizvođača mlijeka.
U pjeni ima previše mjehurića.
Provjerite da li su dva kraja male čelične cjevčice
pravilno postavljeni u cjevčicu za paru.
Dodatak za auto-cappuccino ne uvlači mlijeko
(dodatak se prodaje posebno)
Provjerite da cjevčica uronjena u mlijeko nije
začepljena. Provjerite da li je cjevčica pravilno
namještena sa dodatkom da biste izbjegli curenje.
Najprije isključite aparat i pričekajte da se ohladi prije
nego pristupite čišćenju rupice.
Program čišćenja ne započinje.
Isključite uređaj iz utičnice, pričekajte nekoliko
trenutaka i uključite ga ponovo.
Program uklanjanja kamenca ne počinje.
Isključite aparat iz utičnice, pričekajte nekoliko
trenutaka i uključite ga ponovo.
Spremnik za vodu je pun, ali žaruljica „fill water tank“ i
dalje svijetli.
Provjerite da li je spremnik za vodu pravilno postavljen.
Provjerite da li se posuda na dnu aparata pomiče
lagano. Isperite dijelove uređaja i ako je potrebno,
uklonite kamenac.
Spremnik iskorištene kave je prazan, ali „empty coffee
grounds collector“ žaruljica i dalje svijetli.
Uklonite spremnik iskorištene kave, uvjerite se
da je prazan, pričekajte 8 sekundi i vratite ga na
mjesto.Provjerite da li je posuda za otpatke pravilno
postavljena.
Nestalo je struje u tijeku procesa.
Uređaj će započeti s radom kada ga ponovo uključite i
biće spreman za ponovni proces.
Voda ili kava je ispod uređaja.
Posuda u koju voda kapa je prepuna. Ispraznite je.
Provjerite da li je pravilno postavljena.
„Fault No. XX“ poruka se pojavila na zaslonu.
Isključite uređaj i odnesite ga u servis.Ako greška
potraje, zapamtite broj koji se pojavljuje na zaslonu
ispod poklopca za šalice i kontaktirajte Krups servis.