Filter
Top Products
4
W415-0223 / E / 03.05.09
FOR YOUR SATISFACTION, THIS FIREPLACE INSERT
HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION
AND QUALITY!
Minimum inlet gas supply pressure is 4.5 inches water col-
umn for natural gas and 11 inches water column for propane.
Maximum inlet gas pressure is 7 inches water column for
natural gas and 13 inches water column for propane. Manifold
pressure under fl ow conditions is 3.5 inches water column for
natural gas and 10 inches water column for propane. When
the fi replace is installed at elevations above 4,500ft, and in the
absence of specifi c recommendations from the local authority
having jurisdiction, the certifi ed high altitude input rating shall
be reduced at the rate of 4% for each additional 1,000ft.
Expansion / contraction noises during heating up and cooling
down cycles are normal and to be expected.
Maximum input is 24,000 BTU/hr for natural gas and propane.
Maximum output for natural gas and propane is 20,400 BTU/
hr at an effi ciency of 85% with the fan on. Maximum A.F.U.E.
(annual fuel utilization effi ciency) rating is 79 % for natural gas
and propane. This fi replace insert is not approved for closet or
recessed installations. It is approved for bathroom, bedroom
and bed-sitting room installations and is suitable for mobile
homes. The natural gas model is suitable for installation in a
mobile home that is permanently positioned on its site and
fuelled with natural gas.
This insert must be recessed into a vented noncombustible
wood-burning fi replace (prefabricated or masonry) only. The
minimum fi replace opening size in which the heater is to be
installed is:
HEIGHT 14½ inches
WIDTH 25 inches
DEPTH 11 inches
The minimum allowable chimney fl ue size is 6" round.
The minimum distance, from the bottom of a combustible
mantle projecting 3" maximum from the wall to the top of the
aluminium trim, is 3".
Do not use abrasive cleaners to clean these parts. Buff lightly
with a clean dry cloth.
The glass is 3/16" ceramic glass available from your Napoleon
/ Wolf Steel Ltd. dealer. DO NOT SUBSTITUTE MATERIALS.
Clean the glass after the fi rst 10 hours of operation with a
recommended gas fi replace glass cleaner. Thereafter clean as
required. DO NOT CLEAN GLASS WHEN HOT! If the glass
is not kept clean permanent discolouration and / or blemishes
may result.
THIS GAS FIREPLACE INSERT SHOULD BE INSTALLED
AND SERVICED BY A QUALIFIED INSTALLER to conform
with local codes. Installation practices vary from region to
region and it is important to know the specifi cs that apply
to your area,
for example: in Massachusetts State:
• The fi replace damper must be removed or welded in the open
position prior to installation of a fi replace insert or gas log.
• The appliance off valve must be a “T” handle gas cock.
• The fl exible connector must not be longer than 36 inches.
• The appliance is not approved for installation in a bedroom or
bathroom unless the unit is a direct vent sealed combustion
product.
• WARNING: This product must be installed by a licensed plumber
or gas fi tter when installed within the commonwealth of
Massachusetts.
In absence of local codes, install to the current CAN1-
B149 Installation Code in Canada or to the National Fuel
Gas Code, ANSI Z223.1, and NFPA 54 in the United
States. Mobile home installation must conform with local
codes. In the absence of local codes, install to the current
standard for gas equipped mobile housing CAN/CSA Z240
MH Series in Canada or the manufactured home construc-
tion and safety standard, Title 24 CFR, part 3280, or the
Fire Safety Criteria for manufactured home installations,
Sites and Community Standard ANSI/NFPA 501A in the
United States.
Purge all gas lines with the glass door of the fi replace insert
opened. Assure that a continuous gas fl ow is at the burner
before closing the door.
Under extreme vent confi gurations, allow several minutes
(5-15) for the fl ame to stabilize after ignition.
The fi replace insert and its individual shutoff valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess
of 1/2 psig (3.5 kPa). The fi replace insert must be isolated
from the gas supply piping system by closing its individual
manual shutoff valve during any pressure testing of the gas
supply piping system at test pressures equal to or less than
1/2 psig (3.5 kPa).
A 1/8 inch NPT plug, accessible for test gauge connection,
must be installed immediately upstream of the gas supply
connection to the fi replace insert.
The fireplace insert must be electrically connected and
grounded in accordance with local codes. In the absence of
local codes, use the current CSA C22.1 CANADIAN ELEC-
TRICAL CODE in Canada or the ANSI/NFPA 70-1990 NA-
TIONAL ELECTRICAL CODE in the United States. The blower
power cord must be connected into a properly grounded
receptacle. The grounding prong must not be removed from
the cord plug.
GENERAL INSTRUCTIONS
GENERAL INFORMATION
CARE OF GLASS, AND PLATED PARTS
65.5%
GDIZC