A SERVICE OF

logo

Open as PDF
next previous
83
-
507
-
013 Rev. D
6
CHAPTER 1 GENERAL INF
ORMATION
1.1 USER MANUAL CONTENT
This User’s Manual contains the operating instructions, installation instructions and specifications of
the Genesys
TM
1500W and 750W power supply series. The instructions refer to the standard power
supplies, including the
built
-
in RS232/RS485 serial communication. For information related to oper
a-
tion with the optional IEEE programming, refer to User’s Manual for Power Supply Programming I
n-
terface. (TDK
-
Lambda Americas Inc. P/N 83
-
030
-
200)
1.2 INTRODUCTION
1.2.1
General Descript
ion
Genesys
TM
power supplies are wide output range, high performance switching power supplies. The
Genesys
TM
series is power factor corrected and operates from worldwide AC voltage range contin
u-
ously. Output Voltage and Current are continuously displayed a
nd LED indicators show the complete
operating status of the power supply. The Front panel controls allow the user to set the output p
a-
rameters, the protections levels (Over
-
Voltage protection, Under
-
Voltage limit and Foldback) and pr
e-
view the settings. The
rear panel includes the necessary connectors to control and monitor the power
supply operation by remote analog signals or by the built
-
in serial communication (RS232/RS485).
GPIB pr
o
gramming and Isolated
-
Analog programming/monitoring are optional.
1.2.2
Models
covered by this Manual
Model
Voltage
range (V)
Current
range (A)
Model
Voltage
range (V)
Current
range (A)
GEN 6
-
100
0
-
6
0
-
100
GEN 60
-
12.5
0
-
60
0
-
12.5
GEN 6
-
200
0
-
6
0
-
200
GEN 60
-
25
0
-
60
0
-
25
GEN 8
-
90
0
-
8
0
-
90
GEN 80
-
9
-
5
0
-
80
0
-
9.5
GEN 8
-
180
0
-
8
0
-
180
GEN 80
-
19
0
-
80
0
-
19
GEN 12.5
-
60
0
-
12.5
0
-
60
GEN 100
-
7.5
0
-
100
0
-
7.5
GEN 12.5
-
120
0
-
12
-
5
0
-
120
GEN 100
-
15
0
-
100
0
-
15
GEN 20
-
38
0
-
20
0
-
38
GEN 150
-
5
0
-
150
0
-
5
GEN 20
-
76
0
-
20
0
-
76
GEN 150
-
10
0
-
150
0
-
10
GEN 30
-
25
0
-
30
0
-
25
GEN 300
-
2.5
0
-
300
0
-
2.5
GEN 30
-
50
0
-
30
0
-
50
GEN 300
-
5
0
-
300
0
-
5
GEN 40
-
19
0
-
40
0
-
19
GEN 600
-
1.3
0
-
600
0
-
1.3
GEN 40
-
38
0
-
40
0
-
38
GEN 600
-
2.6
0
-
600
0
-
2.6
GEN 50
-
30
0
-
50
0
-
30
Table 1
-
1: Models covered by the Manual
1.2.3
Features and options
Constant Voltage / Constant Current with automatic crossover.
Active power factor correction.
Universal Input Voltage (85
265Vac), continuous operation.
Embedded Microprocessor Controller.
B
uilt
-
in RS
-
232/RS
-
485 Interface.
Voltage & Current high resolution adjustment by digital encoders.
High accuracy programming/readback.
Software Calibration (no internal trimmers / potentiometers).
Last Setting Memory.
Independent Remote ON/OFF (opto
-
isolat
ed) and remote Enable/Disable.
Parallel operation (Master/Slave) with Active current sharing.