GE JGSP33 Range User Manual


 
AN~-TW
DEWCE
3efom
placing
range
in the counter, notice the
location
of
the stability bracket which is already
attached to the
back
of
the range. This location
should work
for most installations.
However, it
may
be more convenient to hook the stability
chain
to
the unit when the stability bracket is
attached
to
the upper set
of
holes in the back of
the
range.
See Fig. A. The upper level set of holes
are
intended for use with
a
backsplash kit. If
the
backsplash is
not
being used,
make
sure
that
them
tire
nn
structural
supp)rts
for the countertop which
will interfere with the stability bracket when
located
in the upper set of
holes.
Bracket
Optional
/
:,,
,,:
?!
Location
&
; I
!
,
:
,
:
,:
Bracket
.,
:.
Fado~
II
Lo~tion
I::
ii,
a
9
1’
b
,,;
i
:
I
i
il
~
I
i
i‘
\
A
i \
!
1
I
,!
,,
!
I
I
::
Chain
i:
,
2.
Fasten
unc
cnd
of
the stability
chain
to
@
the
fluur
or
wall
with
the
long
screw
and
~
Backguard
4
,.
\
“~
Mainback
Chain
II
I
\
,*
washer-supplied.
See
~~~~er
and
Fig.
B.
Make
certain
the
screw is going
intt)
th~
WUII
plate
at
the
base
t)f
the wall
or
one of the
studs
in the
base
of
the
wall.
Sce
Fig. C. Whether
you
attach
the
chain
to
the wall or
tloor,
be certain
that
the screw
is in
at
Icast
3/4
inch thickness of
wood
other
than
baseb(}ard
and
that
there
are
no
electrical wires or
plumbing in the
area
which the screw
could
pcnetmte.
Attach
the stability
chain
in
a
location
which will allow the
chain
to
be in line with the
bracket side to
aide
as
much
as
possible when
attached
to
the unit. Test to see if the chain is
securely fastened by tugging on the chain.
@
\
A
.
~
Chain
\
Long Screw
,,
Wall Plate
Waaher
3. Temporarily
attach the loose end of the
chain
to
the rear
of
the countertop with the
tape
from
the packaging. See Fig. D.
4.
Place
the
range
in
the
counter
cutout leaving just
enough
mom
between the
back
of the range
and
the
wall
~o
reach
the stability bracket.
5. Hook the loose end of the
chain
onto the
br~cket
by slipping the nearest
link
of
the
chain
into the
slot
in the bracket. See Fig. A
and
make
sure the
chain
is pulled
as
tight as possible and
that
there
is
no
excess
slack
in the
chain
after the
chain
is
attached to
the
bracket.
A
CAUTION: Excessive slack in the chain
could
allow
the range to tip over.
6. Slide the range
all
the way back into the counter.
Once the range is pushed back in place, there will
be
a
small amount of slack in the chain. This
is
nt)rmal.
.----fl.-.
Tape
NOTE:
If attaching to masonry, you
can
buy suitable screws
and anchors at hardware stores. Use
a
m~~sonry
drill
to drill the required
holes.
If range is removed for cleaning or any other reason,
make sure chain is reattached.
35