Liebherr 7082 532-00 Refrigerator User Manual


 
16
Connection
Electric current (alternating current) and voltage
The information on the type plate must conform with the
location. The type plate is located inside the appliance
on the left, fig.A.
The appliance must be connected using a properly
installed shock-proof plug.
The plug must be fused with a 10A or higher fuse, and must
be located outside the rear of the appliance, and must be easy
to access.
The appliance must not
- be connected to stand-alone inverters,
- be operating in conjunction with so-called energy-saving
plugs. This can damage the electronics,
- be connected via an extension lead and with other appliances
- there is a danger of overheating.
When removing the mains cable from the side of the appliance,
remove thecable retainer otherwise there could be vibratory
noise!
Putting into operation and controls
This appliance is not suitable for people (including children)
with physical, sensory or mental problems, or for people who
do not have sufficient experience and knowledge, unless they
are instructed in using the appliance, or are supervised initially
by a person who is responsible for their safety. Children must
supervised, to ensure that they do not play with the appli-
ance.
Avoid continuous skin contact with cold surfaces or with cool
and frozen food. This can cause pain, numbness and freezing.
If you are likely to have extended skin contact, take precau-
tions, such as wearing gloves.
Do not consume edible ice, particularly water ice and ice cubes,
immediately after you have taken them out of the freezer. The
very low temperatures can cause “burning”.
Do not consume food that has been stored for too long, since
this can cause food poisoning.
Installation and ventilation information
When erecting/installing the appliance, make sure
that the coolant pipes are not damaged.
Do not move the ventilation cross-sections.
Always make sure that air can circulate around
the appliance for ventilation purposes!
To comply with the EN 378 standard the position in
which you erect your appliance must indicate a volume of 1 m
for each 8g of R600a coolant
3
so that in the event of a leak from
the coolant circuit a flammable gas/air mixture cannot arise
inside the room where the appliance is positioned. Please see
the type plate inside the appliance for information regarding
the quantity of coolant.
Please also see the appendix of the installation instructions.
Once the appliance is installed: Remove all the transport
safety devices,
- Remove all sticky tape or spacers* from the shelves and adjust
them to the heights you require.
- Remove all protective film: from the decorative strips and the
fronts of the drawers.
We recommend that you clean the appliance before putting it
into operation, please see the section on “Cleaning” for further
information.
The appliance should have been operating for about 2 hours before
you stock it with frozen food. Only place frozen food in the freezer
once the temperature has reached at least -18°C.
Switching on and off
The entire appliance is always switched on at the main
on/off switch 3, both the freezer and the fridge sections.
W Switching on: Press the on/off switch 3 so that the tempera-
ture displays light up/flash.
- Refrigeratorsection: The inside light comes on when the door
is open.
- Freezer section: While the appliance is being put into opera-
tion, and it is still warm, the freezer section display indicates
dashes until the temperature goes below 0°C.
W Switching off: Hold the main on/off switch 3 for about a
second, so that the temperature display turns dark.
W If you only wish to switch off the fridge /BioFresh section (the
freezer stays switched on, useful if going on holiday for example)
then press the on/off switch 9 so that the temperature
display on the fridge 6 and the interior light goes off. The
temperature display on the freezer 5 must remain lit.
Setting the temperature
The appliance is set as standard for normal operation; in the fridge
section we recommend +5°C, and for the freezer -18°C.
Reducing the temperature/colder: Press the relevant Down-but-
ton, on the left for the fridge: 8, on the right for the freezer: 4.
Increase temperature/warmer: Press the relevant Up-button.
- While you are making the adjustment the set value display
flashes.
- The first time you press the temperature setting button, the cur-
rent most recent setting value (= nominal value) appears
on the display.
- If you it press again briefly, the set value changes in 1°C steps,
and if you hold it down, will continue to change.
- About 5 seconds after the final touch of the button, the electron-
ics automatically change the setting, and the actual freezer or
fridge temperature (= actual value) is displayed.
The temperature can be adjusted in the
W fridge section: from 11 °C to 2 °C, in the
W freezer section: from -16 °C to -26 °C.
It depends on where the appliance is located as to whether
the lowest temperature will be reached, in high ambient
temperatures, it may not be possible to achieve the lowest
temperature.
Temperature display
In normal operation:
- the average temperature inside the fridge is 6 and
- the warmest temperature of frozen food 5 is displayed.
The display flashes, if you
- change the temperature setting, or
- if the temperature rises by several degrees, indicating a loss
of cooling capacity, for example warm air can temporarily raise
the temperature when you open the door to store fresh “warm”
1
2
3
4
5
6
8
9
Ventilation
10
7
11
Energy saving information
Make sure the appliance is in a well ventilated position.
Open the appliance doors for as short a time as possible.
Arrange the food in an organised way. Do not exceed stated
storage periods.
Store all food well packed and covered, this avoids frost from
forming.
Allow hot food to cool down to room temperature before plac-
ing inside the appliance.
Allow frozen food to defrost inside the fridge.
In the event of a fault, keep the door closed. This delays the
cold loss. The quality of the frozen food will keep for longer.