Filter
Top Products
33
WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Taking care not to damage the burner electrodes, carefully
lift the hotplate, from underneath disconnect the earth
lead at the right hand rear from the rear cross member
and withdraw the hotplate.
Reassemble in reverse order ensuring that the leads
are reconnected. Take care not to damage the ignition
electrodes of the burners.
It is important that the rear earthing leads are replaced
when the fi xing screws are refi tted as they from part of the
cooker earthing.
Check for correct burner operation.
3. To Remove Side Panels
Disconnect from electricity supply.
Remove the Control Panel - see 1. Pull the cooker forward.
Remove the 4 retaining screws for each panel (1 at the
front base, 1 on the front top and 2 at the rear).
Reassemble in reverse order.
4. To Remove Light Switch
Disconnect from electricity supply.
Remove the Control Panel - see 1.
NB. The old switch may be destroyed during removal.
Remove the old switch from its bezel by griping the switch
body behind the control panel and twisting sharply. The
switch bezel can then be removed by folding back its
locking wings and pushing forward. Fit the new bezel to
the control panel by fi rst lining up the raised key on its
body with the cutout in the control panel and pushing it
in from the front. Assemble the new switch to the bezel by
lining up the key sections and pushing home. Fit the new
button by pushing in from the front.
Replace Control Panel in reverse order and test for correct
operation.
5 To Change an Ignition Switch
Change the gas tap as detailed in Section 9.
6. To Remove Clock
Disconnect from electricity supply.
Remove the Control Panel (See 1). Pull off the timer
control button(s).
Remove the timer/mounting bracket assembly from the
control panel by removing the fi xing screws.
Remove the timer from its mounting bracket by
depressing the plastic lugs on the timer case, at the same
time pulling the unit forward.
Reassemble in reverse order. When replacing leads refer to
the wiring diagram. Check operation of timer.
7. To Remove a Thermostat
Disconnect from the electricity supply.
Remove control panel and hotplate (see 1 & 2). Open oven
door. Remove oven furniture and slide out oven roof liner
if fi tted.
Left hand oven
Pull cooker forward to gain access to the cover box
at the rear of the cooker. Remove the four screws
securing the cover and lift clear. The oven thermostat
capillary is clamped to the oven back sheet with an
earthing plate. Remove the screws and plate.
thermostat capillary
earthing plate
Right hand oven,
The oven thermostat capillary is clamped to the right
hand rear upright with an earthing plate.
Remove thermostat phial cover (2 screws). Unclip the
thermostat phial from the clips in the oven back.
Feed the thermostat capillary out of the oven. Disconnect
wiring from thermostat. Remove 2 screws holding
thermostat to mounting panel. Fit new thermostat
and reassemble in reverse order. Ensure that the phial
is clipped to the oven back with the phial centrally
positioned between the clips.
Remember to refi t the earthing plate.
Check operation of thermostat.
8. To Change the Grill Controller
Disconnect from the electricity supply.
Remove the control panel and hotplate (see 1 & 2).
Disconnect wiring from controller. Remove 2 screws
holding controller to mounting panel. Fit new controller
and reassemble in reverse order. Check for correct
operation.
BEFORE SERVICING ANY GAS CARRYING COMPONENTS
TURN OFF GAS SUPPLY.
9. To Change Hotplate Taps
Disconnect from the electricity supply.
Remove the control panel and hotplate (see 1 & 2).
Undo compression fi tting at the rear of the tap. Remove
the fi xings that secure the tap to the gas rail. Disconnect
the ignition switch wiring.
Remove the tap. Remove and discard the gasket seal.
Fit new gasket seal to replacement tap. Re-assemble in
reverse order. Check the appliance is gas sound. Check
hotplate ignition.