Filter
Top Products
35
WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
18. To Change Tall Oven Door Outer Panel
Remove oven door see 16. Lay door face down on a
suitable surface and remove 2 screws from bottom edge
of door and 2 screws from inside face of door.
Remove outer door panel. Remove door handle by
unscrewing 2 screws. Remove 2 cross-headed screws
holding door handle fi xing bracket to door panel. Fit door
handle bracket and door handle to new panel.
Fit panel to door. Reassemble in reverse order.
19. To Change Tall Oven Door Magnetic Latch
Remove the control panel (see 4).
Remove the plinth (3 screws) and the central vertical cover
(5 screws). Prize the retaining clip off the magnet unit. Fit
new unit and retaining clip.
Reassemble in reverse order.
Check correct door operation.
20. To Remove Grill Element.
Disconnect from electricity supply.
Remove grill pan from grill chamber. From inside grill
compartment remove enamelled front shield from grill
roof, 2 screws and washers. Remove 2 screws and washers
securing the grill element front support. Remove the
screws from the grill elements.
Lift elements out carefully, disconnect the leads from the
element terminals noting their position. If it is not possible
to disconnect the leads in this way, pull cooker forward
to gain access to the rear, remove screws securing the
electric cover to the back sheet and remove cover and
disconnect the terminals from the rear.
Fit new elements, reassemble in reverse order. Check
operation of grill.
21. To Remove Oven Inner Back.
Open the oven door and remove the screws and washers
securing the inner back to the back of the oven.
Carefully lift away the inner back. Reassemble in reverse
order making sure that the 4 screws and washers are fully
tightened.
22. To Change Fan in Oven.
Disconnect from electricity supply.
Pull cooker forward to gain access to the rear. Remove
screws securing the electric cover to the back sheet and
remove cover. Disconnect the 3 terminals connected to
the fan noting their position. Remove oven inner back
(see 20). Hold the fan blade and remove the centre nut
(left hand thread) 2 brass washers, fan blade and Circlip.
Unscrew fan retaining nuts and washers (3 off each) and
lift the fan away from the rear of the cooker. Fit new fan
and reassemble in reverse order. Check operation of oven.
23 To Remove an Oven element Thermal Cut-Out.
Disconnect from the electricity supply.
Pull the cooker for ward to gain access to the cover box.
Undo the cover screws and lift clear. The cutout is located
on the earth plate be side the oven element con nec tions.
Disconnect the cutout wir ing. Undo the fi xings that secure
the cutout to the earth plate and re move. Fit re place ment
control and re-as sem ble in reverse order.
24. To Remove Oven Element.
Disconnect from electricity supply.
Remove oven inner back (see 22).
Remove 2 screws from the top of the element and 1 from
the bottom of the element in side the oven. Lift element
out carefully, disconnect the terminals connected to
the element noting their positions. If it is not possible
to disconnect the leads in this way, pull cooker forward
to gain access to the rear, remove screws securing the
electric cover to the back sheet and remove cover and
disconnect the terminals from the rear.
Fit new element, and reassemble in reverse order. Check
operation of oven.
25. To Remove the Left Hand Oven Bottom & Top
Elements
Disconnect from the electricity supply.
Bottom Element
Pull the cooker forward to access the cover boxes at the
rear of the unit. Remove the fi xings that secure the cover
and lift it clear.
Remove the 2 screws ‘A’ and allow the plate to drop down.
Remove the 2 screws B, lower the upper plate and remove
through the slot in the cooker back.
Undo the terminal connections, noting their positions.