Filter
Top Products
19
Maximum Cooking Time
1. 100%~60% power level : the total cooking time of all cooking stages is maximum 60 minutes.
2. 50%~10% power level : the total cooking time of all cooking stages is maximum 120 minutes.
3. Multi Stage Cooking : the Maximum Cooking Time is limited by the following calculation. Each stage has 100~60% power
level or 50~10% power level.
Maximum Cooking Time Calculation
* Suppose you want to cook 5 minutes at 100% for 1st stage, 15 minutes at 80% for 2nd stage, 40 minutes at 30% for
3rd stage and 20 minutes at 10% for 4th stage. In this case actual Cooking Time is 80 minutes, and the calculated
time is 50 minutes, see the calculation below.
[5min + 15min] + [(40min + 20min)/2]
60 min.
4. 0% power level : maximum 99 minutes and 99 seconds can be input at one stage (max. 4 stages).
5. Express Defrost : the maximum defrosting time is 90 minutes. See Maximum Cooking Time Calculation above.
Total Cooking Time of
100~60% Power Level
60 minutes
2
+
Total Cooking Time of
50~10% Power Level
Monitor
Monitor function is used to check the power level during
cooking.
To check the power level, press the POWER LEVEL pad and
the power level will be displayed. As long as the POWER
LEVEL pad is pressed, the power level is displayed. When
the POWER LEVEL pad is released, the display will return to
the previous display.
Demonstration Mode
To demonstrate, press the MANUAL/REPEAT pad, 0 and
then press the START pad and hold for 3 seconds. Cooking
operations can now be demonstrated with no power in the
oven. The timer will count down rapidly.
To cancel, press the MANUAL/REPEAT pad, then 0 and the
STOP/CLEAR pad or unplug your oven.
To set cooking during the Demonstration mode, press the
MANUAL/REPEAT pad and enter time and press the START
pad. After cooking, press the STOP/CLEAR pad to show
Demonstration again.
When you set Demonstration mode, your oven will not shut
down automatically even if you do not operate the oven for
3 minutes or more.
OTHER CONVENIENT FEATURES
Error Mode
Should any of the error indicators appear in the display, follow the instructions:
EE Mode Reason Action Required
EE1, EE2 Failure of single magnetron Call for service.
★
EE3 Both magnetrons failed Call for service.
EE4 Voltage too high Call for service.
EE5 Voltage too low Call for service.
EE7 Oven cavity or component
temperature too high
It may be caused by poor air circulation. Please, ensure that there is suffi cient
clearance around the oven (see Installation Instructions on page 3) and that
air intake openings are not blocked. Correct the situation if necessary, wait
a few minutes and try again. If problem persists, call for service.
EE8 Circuit failure Call for service.
EE9 Maximum cooking time is
exceeded.
Check the NOTE for Cooking Double/Triple Quantity with Memory on page
6, NOTE 2 for Single Stage Cooking on page 7, or NOTE 2 for Multi Stage
Cooking on page 8 in the Operation Manual.
Press the STOP/CLEAR pad, and re-input by reducing total cooking time
or power levels.
EE0 Cooling fan motor or other motor
failure. Splash cover is not installed
properly.
Cooling fan motor and other motors: Call for service.
Splash cover: Check that Splash cover is properly installed (See page 21).
If problem persists, call for service.
★ EE1 and EE2 : In case of single magnetron failure, oven can be used until servicing by changing Custom Setting, settings
to allow operation under single magnetron only (see page 13). However, check food carefully as additional
cooking time will be needed when operating with a single magnetron.
Press the STOP/CLEAR pad to clear the error indicator. Any time an error code appears, check the reason and be sure to call
for service except EE7 and EE9. As for EE7, follow Action Required and if EE7 is still displayed, be sure to call for service.
R-1900J [EN].indd Sec1:19R-1900J [EN].indd Sec1:19 4/28/09 10:01:29 AM4/28/09 10:01:29 AM