Whirlpool WRF993FIFM Refrigerator User Manual


 
20
Using the Controls
The temperature control is located across the top of the refrigerator cabinet behind the doors.
Meats
Drinks
Deli/Cheese
Drawer
Fridge
Freezer
Recommended
SHOWROOM
POWER OUTAGE
Icemaker2
Fast Cool
Energy Saver
Cooling O
˚F
˚C
hold 3 sec
for Filter Reset
IMPORTANT: The display screen on the temperature control
panel will turn off automatically when the door is closed. Touch
any control button to reactivate the display screen. The home
screen will appear as shown.
Viewing and Adjusting Temperature Set Points
For your convenience, your refrigerator, freezer, and pantry
drawer controls are preset at the factory.
When you rst install your refrigerator, make sure that the
controls are still set to the recommended set points. The factory
recommended set points are 37°F (3°C) for the refrigerator and
0°F (-18°C) for the freezer.
IMPORTANT:
Wait 24 hours before you put food into the refrigerator. If you
add food before the refrigerator has cooled completely, your
food may spoil.
NOTE: Adjusting the set points to a colder-than-
recommended setting will not cool the compartments
any faster.
The recommended settings should be correct for normal
household use. The controls are set correctly when milk or
juice is as cold as you like and when ice cream is rm.
NOTE: Areas such as a garage, basement, or porch may have
higher humidity or extreme temperatures. You may need to
adjust the temperature away from the recommended settings
to accommodate for these conditions.
Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
View Temperature Set Points
1. Touch DRAWER, FRIDGE, or FREEZER to activate
Temperature mode.
NOTE: To view temperature in degrees Celsius, touch
and hold the ˄ (up) or ˅ (down) arrows simultaneously for
3 seconds and the temperature display will change. To return
to Fahrenheit, touch and hold the ˄ (up) or ˅ (down) arrows
simultaneously for 3 seconds and the temperature display
will change.
To activate Temperature mode, touch FRIDGE or FREEZER
and use the ˄ (up) or ˅ (down) arrows to change temperature.
The display will show the temperature set point of the
selected compartment, and then temperature adjustment will
appear in the display.
To activate Temperature mode for Pantry Drawer, touch
DRAWER and toggle through 3 optional temperature settings:
Meats (raw meat/sh/chicken); Drinks; Deli/Cheese (deli/lunch
meat/cheese). The display will show the temperature set point
of the selected setting for the Pantry Drawer. Actual Pantry
Drawer temperature performance is dependent upon the
refrigerator compartment temperature.
Recommended Refrigerator Temperature
Recommended Freezer Temperature
Adjust Temperature Set Points
Refrigerator set point range: 33°F to 42°F (0°C to 5.5°C)
Freezer set point range: -5°F to 5°F (-21°C to -15°C)
1. To activate Temperature mode, touch FRIDGE to select the
Refrigerator zone. The display will show the temperature set
point of the selected compartment as shown.
2. Touch ˄ (up) arrow to raise the set point or touch ˅ (down)
arrow to lower the set point. New setting is automatically
saved.
3. To adjust Freezer, change the display to show the freezer
set point.
4. Touch the ˄ (up) arrow to raise the set point or touch
the ˅ (down) arrow to lower the set point. New setting is
automatically saved.
5. The drawer set points for Meats, Drinks and Deli/Cheese are
preset. Touch DRAWER once for meats, twice for drinks, and
3 times for deli/cheese, depending on what is being put in the
drawer.
When adjusting temperature set points,
use the following chart as a guide:
CONDITION: TEMPERATURE ADJUSTMENT:
Refrigerator too cold Refrigerator Setting 1° higher
Refrigerator too warm Refrigerator Setting 1° lower
Freezer too cold Freezer Setting 1° higher
Freezer too warm/
too little ice
Freezer Setting 1° lower