Garmin 210 GEO T DL Range User Manual


 


28
Servicing
When servicing or replacing gas carrying components
disconnect from gas before commencing operation
and check appliance is gas sound after completion.
When checking for gas leaks use a liquid leak detector
at all joints and connections to check for leaks in the
system. Use a product specifically manufactured for leak
detection. In GB refer to BS 6891.
Leak testing of the appliance shall be conducted in
accordance to the manufacturer’s instructions.


Do not use re-conditioned or unauthorised gas controls.
Disconnect from the electricity supply before
commencing servicing, particularly before removing
any of the following: control panel, side panels, hotplate
tray or any electrical components or covers.
Before electrical re-connection, check that the appliance
is electrically safe.
Note: References to LH and RH oven apply as viewed
from the front.
BEFORE SERVICING ANY GAS CARRYING COMPONENTS.
TURN OFF THE GAS SUPPLY.
 
Disconnect the appliance from the electricity supply.
a) Pull the unit forward to gain access.
b) Remove the pan supports/hotplate accessories
and burner caps.
c) Remove the brass venturi in the centre of each
hotplate burner bezel.
d) Remove the bezel from the hotplate and
disconnect the spark ignition lead from the spark
electrode.
e) Lift the hotplate clear of the appliance.
f) Replace in reverse order.
 
Disconnect the appliance from the electricity supply.
a) Remove the pan supports/hotplate accessories
and burner caps.
b) Slacken the brass venturi at the centre of each
burner.
c) Remove the control knobs from all taps.
d) Open the grill and RH oven doors. Remove 3
fixings on the top front and 3 fixings on the control
panel underside.
e) Pull the control panel forward. Remove the
connections from the rear of the three neons.
Disconnect the earth lead and lift the panel clear
of the unit.
f) Replace all parts in reverse order.
g) When replacing any electrical connections refer to
the wiring diagram.
 
Disconnect the appliance from the electricity supply.
a) Remove the control panel as detailed in Section 2
b) Remove the retaining screw on the upper front
edge and the two fixings on the rear or the side
panel. Undo the lower retaining screw situated
below the edge at the panel front corner.
c) Remove the panel by pulling it away from the
unit. Should difficulty be encountered, it may be
necessary to slacken the two closest burners and
both brass venturi as detailed in Section 1.
d) Replace parts in reverse order. Ensure that both
venturis are fully tightened.
 
Disconnect the appliance from the electricity supply.
a) Remove the control panel as detailed in Section 2
b) Remove the relevant neon connection and undo
the nut which secures the neon to the control
panel.
c) Replace parts in reverse order. Ensure the
replacement neon functions correctly.
 
Disconnect the appliance from the electricity supply.
a) Remove the hotplate as detailed in Section 1.
b) Remove the control panel as detailed in Section 2
c) Open the appropriate oven door and remove the
oven shelves.
d) Pull the unit forward to gain access to the cover
box. Undo the cover screws and lift clear.

Remove the two fixings that secure the
thermostat phial cover. Unclip the thermostat
phial from the clips in the oven back panel.

Remove the two screws holding the thermostat
phial to the oven fan cover at the rear of the oven.
Pull the unit forward to access the rear of the
cooker. Remove the both cover boxes by removing
the fixing screws and lifting clear. Feed the
thermostat capillary clear of the oven.
d) Disconnect the wires from the thermostat and
undo the two fixings which secure the control to
the mounting plate.
e) Fit the replacement and re-assemble in reverse
order. Ensure that the phial is clipped to the oven
rear, positioned centrally between the clips. Check
that the thermostat functions correctly.