Garmin 210 GEO T DL Range User Manual


 


29
 
Disconnect the appliance from the electricity supply.
a) Remove the hotplate as detailed in Section 1.
b) Remove the control panel as detailed in Section 2.
c) Disconnect the controller wiring. Undo the fixings
that secure the device to the mounting plate.
d) Fit the replacement and re-assemble parts
in reverse order. Check that the replacement
functions correctly.
 
Disconnect the appliance from the electricity supply.
a) Pull the unit forward to gain access to the cover
box. Undo the cover screws and lift clear.
b) The control is located on the earth plate beside the
oven element connections.
c) Disconnect the thermostat wiring. Undo the
fixings that secure the thermostat to the earth
plate and remove.
d) Fit replacement control and re-assemble parts in
reverse order.
 
a) Remove the hotplate as detailed in Section 1.
b) Remove the control panel as detailed in Section 2.
c) Unplug the FSD lead from the rear of the tap. Undo
compression fitting at the rear of the tap. Remove
the fixings that secure the tap to the gas rail.
Disconnect the ignition switch wiring.
d) Remove the tap. Remove and discard the gasket
seal. Fit new gasket seal to replacement tap.
e) Re-assemble in reverse order. Check the appliance
is gas sound. Check hotplate ignition.
 
Change the gas tap as detailed in Section 8.
 
a) Remove the hotplate as detailed in Section 1.
b) Remove the injector directly from the burner body.
c) Fit the appropriate injector.
d) Re-assemble in reverse order. Check the appliance
is gas sound.
 
a) Remove the pan supports, hotplate accessories
and burner heads.
b) Undo the bezel venturi and remove the bezel from
the hotplate. The spark ignition wire will be pulled
through the electrode clearance hole.
c) Disconnect the spark electrode from the ignition
wire.
Take care to prevent the ignition wire from
falling back through the clearance hole.
d) Undo the spark electrode from the bezel by
removing the spring clip and spring.
e) Fit the replacement electrode to the burner
bezel. Ensure that the spring and clip are properly
located.
f) Replace in reverse order and check correct burner
ignition.
 
a) Remove the pan supports, hotplate accessories
and burner heads.
b) Remove the hotplate as detailed in Section 1.
c) Undo the compression fitting which connects the
burner body to the gas pipe.
d) Remove the nut that secures the burner body to
the support channel.
e) Remove the fixings that secure the support
channel to the chassis. Lift the channel clear of the
appliance.
f) Remove the burner body from the appliance.
g) Replace in reverse order. Check the appliance
is gas sound and that the burner operates
satisfactorily.
 
a) Open the oven door.
b) Support the door and remove the two screws
which secure the upper hinge to the front frame of
the unit.
c) Remove the door from the lower hinge by lifting
slightly and moving it outward.
d) Re-assemble in reverse order.
 
a) Remove the pan supports, hotplate accessories
and burner heads.
b) Remove the hotplate as detailed in Section 1.
c) Remove the control panel as detailed in Section 2
d) Remove LH side panel a detailed in Section 3.
e) Remove the plinth (3 screws).
f) Remove the central vertical cover situated
between the ovens. (5 screws).
g) Remove the 2 countersunk screws (1 per side)
which secure the hinge arms to the front of the
grill chamber.
The door hinge arms are spring tensioned.
Carefully remove the grill door and retain the gaskets.
h) Re-assemble in reverse order. Ensure that the
gasket is fitted between the hinge arm and the
front of the grill chamber. Check door operation.