Filter
Top Products
5 189159000
INSTALLATION
This section covers unpacking and inspection, identi-
fication of LOOSE--SHIPPED PARTS, selecting loca-
tion, installing unit, preparing unit for operation, and
unit operation.
UNPACKING AND INSPECTION (see Figure
3)
NOTE: The unit was thoroughly inspected before
leaving factory and carrier has accepted and
signed for it. Any damage or irregularities
should be noted at time of delivery and immedi-
ately reported to delivering carrier. Request a
written inspection report from Claims Inspector
to substantiate any necessary claim. File claim
with delivering carrier, not with IMI Cornelius Inc.
1. After unit has been removed from shipping car-
ton, remove shipping tape and other packing
material. Inspect for shipping damage and follow
procedure in preceding NOTE if damage is evi-
dent.
2. Unpack item listed in LOOSE--SHIPPED
PARTS. Make sure all items are present and in
good condition.
Table 2. Loose-Shipped Parts
Item
No. Part No. Name Qty.
1 188090 Leveling Legs 4
2 186642 Cup Rest 1
3 186573--039 Drip Tray 1
4 151741--039 Dispensing Valve
Knob
4
5 150807--100 Adapter, 7/16--20
Male by 1/2--16 Male
4
150807--200 Adapter, 1/2--16
Male by 1/2--16 Male
(domestic unit only)
4
6 311245 Reducer, 7/16--20
Female by 1/2--16
Male
4
7 317904--999 Decal, Dispensing
Valve Knob (as
ordered)
4
IDENTIFICATION OF LOOSE--SHIPPED
PARTS (see Figure 3)
1. LEVELING LEGS (item 1) to be installed in
threaded holes provided on unit base (only units
installed outside the United States).
2. CUP REST (item 2) to be installed in DRIP
TRAY
(item 3).
3. DRIP TRAY (item 3) to be installed on unit by
inserting rear edge of tray under lip of valve trim
panel and lifting up until bottom tray supports
are inserted in square holes provided in front
panel. Lock drip tray in place by slight down-
ward pressure.
4. DECALS, DISPENSING VALVES KNOBS (item
7) to be installed on DISPENSING VALVES
KNOBS (item 4)
5. DISPENSING VALVES KNOBS (item 4) to be
installed on dispensing valves by pushing knobs
down into place on valves levers.
6. Applicable ADAPTERS (item 5) to be used to
connect product inlet lines from product tanks to
unit product inlet lines. REDUCERS (item 6)
may be used to connect unit product inlet lines
directly to product tanks quick disconnects pro-
vided disconnects have 1/4--inch flare (7/16--20)
male fittings.
SELECTING LOCATION
NOTE: For identification purposes, side of unit
dispensing valves are on is designated ‘ ‘front’’ of
unit. This unit may be installed free standing or
under counter or bar. Locate unit so following
requirements are satisfied.
1. Near a properly grounded electrical outlet with
proper electrical requirements. No other electri-
cal appliance should be connected to this circuit.
ALL ELECTRICAL WIRING MUST CONFORM
TO NATIONAL AND LOCAL ELECTRICAL
CODES.
2. Air circulation through condenser coil, required
for cooling coil, is drawn in through air intake
grille on front of unit and is exhausted out
through grilles on sides and back of unit. When
locating unit, make sure grilles are not restricted
to insure proper air circulation through unit.
INSTALLING UNIT
LOCATING UNIT
Areas Outside United States (Canada, Europe, etc.)
Install LEVELING LEGS (item 1) in threaded holes
on each corner of unit base. Adjust each leveling leg
until unit sits level and stands solid. Make sure all
leveling legs are in contact with floor.
Areas Within United States -- To comply with National
Sanitation Foundation (NSF) requirements, unit must
be sealed to floor and LEVELING LEGS (item 1)
may not be used. Perform following procedure to
install unit.