Filter
Top Products
Appendix: Quick Reference Overview
56
User Manual WMF presto
Appendix A: Quick Reference Overview
Order Number 33 2319 9010
Edition 1.02 - 10.05
Quick Reference Installation Instructions
For initial startup on delivery ex works.
Please refer to WMF presto User Manual. Pay special attention to the hazard
notices and Safety chapter.
Unpacking
Unpack the WMF presto and place it on a fi rm horizontal surface.
Mains Connection
Connect mains cable to a fused three-pin power point.
Mains Required:
(Kindly note the required Mains Power and Voltage as shown on the type label of the
machine)
230V/50Hz, fuse 10A minimum!
Japan- 200V/50/60Hz, (2000W) fuse 15A minimum!
USA - 120V/50Hz, (1700W) fuse 15A minumum!
Switch On
Press and hold ON/OFF button for 2 sec min..
WMF presto switches on and startup program commences.
The WMF presto takes you using step by step dialogues through the
installation routine. Perform each step only when instructed on the display!
Removing Water Tank
Remove water tank, remove lid.
Take out accessory components contained.
Water tank option only!
Rinse out water tank and fi ll with clean cold mains water.
Place lid on water tank and replace until it meets the stop.
Removing Coffee Grounds Container
Push combi spout fully upwards.
Push up adjustable screen over coffee grounds container.
Remove coffee grounds container and remove accessories.
Replace coffee grounds container until it meets the stop.
Close adjustable screen.
Constant Water Supply (optional)
Carefully insert seals attached to connecting tube.
Using hose connect union on rear of machine to existing water tap or anti-scale fi lter
as appropriate.
If using WMF AquaQuell 1.5 Filter System follow its User Manual.
Turn on water.
Check unions for leaks and tighten if necessary!
Drain Outlet (optional)
Push drain tube with angle onto water drain connector on rear of machine.
Connect drain tube to mains drain via an S-trap
Tube must not sag. Shorten tube if necessary!
Packaging material in box contains accessories!
Do not throw away!
For accessories and identifi action of machine
components see User Manual!
Make sure that the coffee machine is in perfect
condition. In the event of doubt do not start up
and inform WMF Service.
Keep original packaging in the event of any
subsequent return!
For installation terms and conditions see
User Manual!
Do not loosen any screws and do not remove
any housing parts - there is danger to life inside
the machine due to mains voltage!
Siphon = S-bend (odour trap)
(as on dishwahers)
Recipe setting adjusted to new cup volumes!
Coffee machine is rinsed out on dispensing
the first three beverages. Dispose of the first
three beverages dispensed!
Readiness State display
with one button level
Readiness State display
with two button levels
Level 1 active Level 2 active
Do not jam milk hose and if fitted choc hose!
Do not confuse beans and powder containers!
The WMF presto takes you using step by step dialogues through the
installation routine. Perform each step only when instructed on the display!
Set Water Hardness
Request water hardness reading from water supplier or determine using
WMF Carbonate Hardness Test Kit (complete with Instructions) in the accesssories.
Labelled “Deutsche Karbonathärte” = ° dKH
Fill Product Reservoir
Fill Product Reservoir when requested by display.
Connect Fresh Milk (optional)
Open milk lid fully to the front.
Open fresh milk pack so that it is lying on the thin side and no milk runs out.
Push preassembled milk hose into the milk pack. Shorten hose as required.
Place milk pack carefully in the chute.
When adjusting height of combi spout, hose must not be stretched.
Replace milk lid.
Cooler (optional)
Punch pre-stamped knock-out on milk lid.
Feed tube through and push into cooler.
When adjusting height of Combi spout, hose must not be stretched.
green Milk nozzle =• cold milk
white Milk nozzle =• milk at room temperature
Set Cup Volumes
Decide beverage receptacles for beverage dispensing and keep receptacles ready.
This point can be skipped if beverage receptacles are not available.
Touch beverage button for the desired beverage.
Activate test dispensing by touching
.
Adjust cup volumes with and pads.
Save with
.
Second Button Level (optional)
If your WMF presto has a second button level you can also set the cup volumes for the
beverages of the second button level. If the second level is available the toggle pad will
be displayed.
Activate the respective inactive button level by touching the toggle pad.
The selected settings may now be adjusted at any time in the Setting Menu.
Setup Complete
The dialogue is now ended. Your WMF presto is now ready for operation.
Please find out how to set, operate, clean and program your coffee machine in your User
Manual..
Beverage Despensing
Pressing the beverage buttons triggers dispensing of the beverage set.
Illuminated ring round button
= ready
Flashing ring round button
= dispensing
Place receptacle underneath
Press desired beverage button
Chosen beverage and progress of dispensing are shown in the display.
We wish you every success with your WMF presto!
•
•