A SERVICE OF

logo

Open as PDF
next previous
TABLE OF
CONTENTS
WARRANTY…………………………………………………………………………………………….
Pg. 1
SAFETY INSTRUCTIONS……………………………………………………………………………..
Pg. 2
GERMAN SAFETY INSTRUCTIONS…………………………………………………………………
Pg. 4
CHAPTER 1 GENERAL INFORMATION
…………………………………………………………...
Pg. 6
1.1 USER MAN
UAL CONTENT……………………………………………………………………….
Pg. 6
1.2 INTRODUCTION……………………………………………………………………………………
Pg. 6
1.2.1 General description…………………………………………………………………………..
Pg. 6
1.2.2 Models covered ……………………………………………………………………………...
Pg. 6
1.2.3 Featu
res and options ………………………………………………………………………..
Pg. 6
1.2.4 Multiple output power system ………………………………………………………………
Pg. 7
1.2.5 Control via the serial communication port…………………………………………………
Pg. 7
1.2.6 Analog voltage programming and monitor
ing…………………………………………….
Pg. 7
1.2.7 Parallel operation…………………………………………………………………………….
Pg. 7
1.2.8 Output connections………………………………………………………………………….
Pg. 7
1.2.9 Cooling and mechanical construction……………………………………………………..
Pg. 8
1.3 ACCESSORIES
…………………………………………………………………………………….
Pg. 8
1.3.1 General………………………………………………………………………………………..
Pg. 8
1.3.2 Serial link cable………………………………………………………………………………
Pg. 8
1.3.3 Misc. hardware……………………………………………………………………………….
Pg. 8
1.3.4 AC cables
…………………………………………………………………………………….
Pg. 8
CHAPTER 2 SPECIFICATIONS
……………………………………………………………………...
Pg. 9
2.1 OUTPUT RATING………………………………………………………………………………….
Pg. 9
2.2 INPUT CHARACTERISTICS……………………………………………………………………...
Pg. 9
2.3 CONSTANT VOLTAGE MODE…………
………………………………………………………...
Pg. 9
2.4 CONSTANT CURRENT MODE…………………………………………………………………..
Pg. 9
2.5 ANALOG PROG
R
AM
M
ING AND MONITORING……………………………………………….
Pg. 9
2.6 PROGRAMMING AND READBACK……………………………………………………………..
Pg. 10
2.7 PROTECTIVE FUNCTIONS……………………………………
…………………………………
Pg. 10
2.8 FRONT PANEL…………………………………………………………………………………….
Pg. 10
2.9 ENVIRONMENTAL CONDITIONS……………………………………………………………….
Pg. 10
2.10 MECHANICAL…………………………………………………………………………………….
Pg. 10
2.11 SAFETY/EMC……………………………………………………………………………………..
Pg. 10
2.12 SUPPLEMENTAL CHARACTERISTICS……………………………………………………….
Pg. 11
2.13 OUTLINE DRAWINGS…………………………………………………………………………...
Pg. 12
CHAPTER 3 INSTALLATION
………………………………………………………………………..
Pg. 13
3.1 GENERAL…………………………………………………………………………………………...
Pg. 13
3.2 PREPA
RATION FOR USE………………………………………………………………………...
Pg. 13
3.3 INITIAL INSPECTION……………………………………………………………………………...
Pg. 13
3.4 RACK MOUNTING…………………………………………………………………………………
Pg. 13
3.4.1 To install the power supply in a rack……………………………………………………..
Pg. 14
3.4.2 Rack mount slides………………………………………………………………………….
Pg. 14
3.5 LOCATION MOUNTING AND COOLING……………………………………………………….
Pg. 14
3.6 AC SOURCE REQUIREMENTS………………………………………………………………….
Pg. 14
3.7 AC INPUT POWER CONNECTION……………………………………………………………...
Pg. 15
3.7.1 AC input connector………………….………………………………………………………
Pg. 15
3.7.2 AC input cord………………………………………………………………………………..
Pg. 15
3.7.3 AC input wire connection………………….………………………………………………..
Pg. 15
3.8 TURN
-
ON CHECKOUT PROCEDURE……………………………………………
…………….
Pg. 17
3.8.1 General……………………………………………………………………………………….
Pg. 17
3.8.2 Prior to operation…………………………………………………………………………….
Pg. 17
3.8.3 Constant voltage check……………………………………………………………………..
Pg. 17
3.8.4 Constant current check…
…………………………………………………………………..
Pg. 17
3.8.5 OVP check…………………………………………………………………………………...
Pg. 18
3.8.6 UVL check……………………………………………………………………………………
Pg. 18
3.8.7 Foldback check……………………………………………………………………………...
Pg. 18