Filter
Top Products
Epson PowerLite 7900p Projector
9/04 Epson PowerLite 7900p Projector - 13
4. Hold down the
Num button
on the remote control and use
the numeric keypad to enter a
4-digit password.
The password will be
displayed as
****. After you
enter the last digit, a
confirmation screen appears.
Enter the password again.
5. After you finish setting the
password, press the
ESC
button to return to the
Password Protect menu.
6. Press the
Num button to deactivate the numeric keypad.
Make a note of the password and keep it in a safe place in case
you forget it.
Creating a User’s Logo
You can transfer any image on your computer to the projector,
and then use it as the startup screen and/or the screen that is
displayed when you press the
A/V Mute button. The image
can be a company logo, slogan, photograph, or any other
image you want to use.
Follow these steps to capture the image and transfer it to the
projector:
1. Display the image you want to use on the projector. You
can use an image from either a computer or video source,
such as a VCR.
2. Press the
Menu button and select the User’s Logo menu.
3. Press
Enter to select Execute.
Note: If the
User’s Logo Protect option is ON, you see a
message that the logo cannot be recorded. You’ll need to
disable
User’s Logo Protect before you can create or change
the logo. See the next section, “Turning On the Password and
User’s Logo.”
4. When you see a message asking if you want to use the
present image as a user’s logo, select
Yes and press Enter. A
selection box displays over the image.
5. Use the pointer button on the remote control to select
the area of the image you want to use. Once you’ve selected
the area, press
Enter.
6. When you see the message
Select this image?, choose Yes
and press
Enter. If you want to change the area selected,
select
No, press Enter, and repeat steps 4 through 6.
7. When you see this screen, select a zoom rate (display size),
and then press
Enter.
8. When you see the message
Save image as user’s logo?,
select
Yes and press Enter. Saving the logo takes about 15
seconds. Do not use the projector or other sources
(computer, video, etc.) while the logo is being saved.
9. When you see the message
Completed, press ESC.
Turning On the Password and User’s Logo
To enable the password and User’s Logo, follow these steps:
1. Press the
Freeze button on the remote control for about 5
seconds until you see the Password Protect menu.
2. Select
Power ON Protect and press Enter.
3. Select
ON and press ESC.
4. If you want to disable the password temporarily, select
Timer and press Enter. Then hold down the Num button
while you use the numeric keypad to enter the number of
hours (from 0 to 9999) you want the password feature
disabled. If you want the projector to request the password
every time it is turned on, set the timer to
0H.
The timer starts counting as soon as you close the Password
Protect menu. (You can check the elapsed time in this menu
next to
Time elapsed.)
When the period defined in the Time-elapsed setting has
passed, and the password is entered correctly, the elapsed
time will be reset to
0H and the timer will start again.
Remember to disable or change this setting when you’re
finished using it.
5. To enable your User’s Logo, select
User’s Logo Protect and
press
Enter. Then select ON and press Enter.
When this feature is on, the logo appears whenever the
projector is turned on (if the
No-Signal Msg is set to Logo
in the Setting menu) and as the A/V Mute screen (if you
selected
Logo as the A/V Mute setting in the Setting menu).
Note: None of the User’s Logo features can be changed when the
User’s Logo Protect function is enabled.
6. Press
Menu to close the Password Protect menu.
7. Turn off the projector and unplug the power cord to enable
password protection.
Num button Numeric keypad
Set the zoom rate.
Zoom rate:
Zoom rate:
100% 200% 300%
User's Logo