Filter
Top Products
5
DISPENSE TIME (Seconds)
DISPLAY
Increase Decrease
Readout will be displayed for 5 minutes.
Timer can only be adjusted
while readout is displayed.
+
WARNING
HAZARDOUS VOLTAGE
UNPLUG GRINDER
BEFORE REMOVING!
I 0.0
P734
-
+
F
U
N
C
-
+
F
U
N
C
-
+
F
U
N
C
P927
NOTICE
For connection to Bunn-Omatic
Coffee Brewer Models:
Dual, OT, Single, & System III only.
(24 volt N.E.C. Class 2 circuit only.)
B
U
N
N
M
A
N
U
F
A
C
T
U
R
E
D
B
Y
B
U
N
N
-O
-M
A
T
IC
C
O
R
P
O
R
A
T
IO
N
S
P
R
IN
G
F
IE
L
D
, IL
L
IN
O
IS
, U
.S
.A
.
M
O
D
E
L
S
/N
V
O
L
T
S
A
.C
. A
M
P
W
A
T
T
S
P
H
A
S
E
W
IR
E
H
E
R
T
Z
C
O
V
E
R
E
D
U
N
D
E
R
O
N
E
O
R
M
O
R
E
O
F
T
H
E
F
O
L
L
O
W
IN
G
P
A
T
E
N
T
S
:
O
N
E
O
R
M
O
R
E
O
T
H
E
R
P
A
T
E
N
T
S
M
A
Y
B
E
P
E
N
D
IN
G
NOTICE
NOTICE
The Shipping Bracket and
All Packing Material
Behind This Panel
MUST be Discarded
Before Using Grinder!
(Refer to the Operating & Service Manual for
Additional Set-up Information.)
P928
PP927
DG-2 INITIAL SET-UP
1. WARNING - Unplug grinder before removal of any panel.
2. Read NOTICE attached to upper front inspection panel.
3. Remove upper front inspection panel located below control switches and
the rear panel.
4. Remove shipping bracket, materials and discard.
5. Reinstall upper front inspection panel and rear panel.
6. Open the top lid(s). Clear all foreign objects and shipping material from the
hopper compartments and the entrance to the grind chambers.
7. Remove the lower front inspection panel.
8. Plug-in the grinder.
9. Select either the left or right hopper with the selector switch. Do not press
the start switch.
10. The dispense timer panel readout will indicate the present timer setting in
seconds and will remain displayed for five minutes.
11. Increase or decrease the timer setting to obtain the desired amount of cof-
fee for the hopper selected by pressing the appropriate button (+ or –).
12. Repeat steps 9 thru 11 for the other hopper. The display will go out on its
own. Reinstall lower front inspection panel.
13. Fill the hopper compartments with whole bean coffee. (Capacity 6 pounds
each). The grinder is now ready for use.
WDG-2 INITIAL SET-UP
1. WARNING - Unplug grinder before removal of any panel.
2. Read NOTICE attached to the upper front inspection panel.
3. Remove upper front inspection panel located below control switches and
the rear panel.
4. Remove shipping bracket, materials and discard.
5. Reinstall upper front inspection panel and rear panel.
6. Open the top lid(s). Clear all foreign objects and shipping material from the
hopper compartments and the entrance to the grind chambers.
7. Remove the four screws securing the lower front inspection panel and care-
fully pull out far enough to view and operate the digital control display
assembly.
8. Plug-in the grinder.
9. Select either the left or right hopper with the selector switch. Do not press
the start switch.
10. The digital control display assembly screen displays selected weight when
idle. When grinding - display resets to 0.00 and shows increasing weight.
Display shows final weight for ten seconds and returns to selected weight.
11. Use (+) or (-) buttons and left or right hopper selector switch to set selected
weights, .50 oz minimum - 16 oz maximum.
NOTE: Refer to function list on page 8 for recalibration of weigh control
assembly if necessary.
10854 030300