Cuisinart FP-14 Food Processor User Manual


  Open as PDF
of 93
 
18
7. Problem: Nub of dough forms on top of
blade and does not become uniformly
kneaded.
Solution:
 r4UPQNBDIJOFDBSFGVMMZSFNPWFEPVHI
divide it into 3 pieces and redistribute
them evenly in the work bowl.
8. Problem: Dough feels tough after kneading.
Solution:
 r
Divide dough into 2 or 3 pieces and
redistribute evenly in bowl. Process 10
seconds or until uniformly soft and pliable.
9. Problem: Dough is too dry.
Solution:
 r8IJMFNBDIJOFJTSVOOJOHBEEXBUFS
tablespoon at a time until dough cleans
the inside of the bowl.
10. Problem: Dough is too wet.
Solution:
 r8IJMFNBDIJOFJTSVOOJOHBEEGMPVS
tablespoon at a time until dough cleans
the inside of the bowl.
Technical
1. Problem: The motor does not start.
Solution:
r5IFSFJTBTBGFUZJOUFSMPDLUPQSFWFOUUIF
motor from starting if it is not properly
assembled. Make sure the work bowl
and work bowl cover are securely locked
into position.
r*GZPVBSFTMJDJOHPSTISFEEJOHBOEUIF
above solution does not work, make sure
that the food contents in the feed tube are
cut below the maximum fill line so that the
activation rod can engage the motor.
r*GUIFNPUPSTUJMMXJMMOPUTUBSUDIFDLUIF
power cord and outlet.
2. Problem: The food processor shuts off during
operation.
Solution:
r5IFDPWFSNBZIBWFCFDPNFVOMPDLFE
check to make sure it is securely in
position.
r"TBGFUZQSPUFDUPSJOUIFNPUPSQSFWFOUTUIF
motor from overheating, which is caused by
excessive strain. Press the Off control
button and wait 10 to 15 minutes to allow
the food processor to cool off before
resuming.
3. Problem: The food processor cover becomes
unlatched in the back and/or makes a loud
noise.
Solution:
r5IFCBDLPGUIFDPWFSCFDPNJOHVOMBUDIFE
and any related noise, will not prevent the
unit from working. Simply push down to
lock the back into position.
4. Problem: The motor slowed down during
operation.
Solution:
r5IJTJTOPSNBMBTTPNFIFBWJFSMPBETFH
slicing/shredding cheese) may require the
motor to work harder. Simply reposition the
food in the feed tube and try again.
r5IFNBYJNVNMPBEDBQBDJUZNBZIBWFCFFO
exceeded. Remove some of the ingredients
and continue processing.
5. Problem: It is difficult to remove the
chopping/mixing blade from the work bowl.
Solution:
r5IFTFJOOPWBUJWFCMBEFTIBWFCFFO
designed to lock in the work bowl to
prevent them from falling out when
emptying the contents of the bowl. Using
extreme care, use a little extra force to
remove the blade.
6. Problem: The food processor vibrated/
moved around the countertop during
processing.
Solution:
r.BLFTVSFUIFSVCCFSGFFUBUUIFCPUUPNPG
the unit are clean and dry. Also make sure
that the maximum load capacity is not
being exceeded.
r5IJTJTOPSNBMBTTPNFIFBWJFSMPBETFH
slicing/shredding cheese) may require the
motor to work harder.
7. Problem: The large pusher falls out when the
cover is turned upside down.
Solution:
r5IFQVTIFSMPDLGFBUVSFMPDBUFEBCPWFUIF
handle, should be pulled out.
 previous next