Filter
Top Products
III. d - INSTALLING LEGS OR CASTERS (cont’d):
box(es), it should contain either four (4) legs or casters
(RBC50 x 8 or RBC100 x 4 and four bolts for each caster).
WARNING: THE CABINET MUST BE BLOCKED AND
STABLE BEFORE INSTALLING LEGS OR CASTERS.
To install the legs or casters, first raise and block the
unit a minimum of 7” from the floor. For installing legs,
thread the legs into the threaded holes on the bottom of
the cabinet (see figure 1). Be certain that all legs are
tightened securely. When the unit is set in its final posi-
tion, it is important for proper operation that the unit be
level. The legs are adjustable for this purpose, turn the
bottom of the leg counter-clockwise to raise it, clock-
wise to lower it. Level the unit from front to back as well
as side to side in this manner, using a level placed in the
bottom of the cabinet.
Please note that Traulsen units are not designed to be
moved while on legs. If the unit requires moving, a pal-
let jack or forklift should be used to prevent damage.
For installing casters, the casters are “plate” type, and
require the use of four (4) bolts each to secure them
firmly to the cabinet bottom at each corner (see figure
2). The caster bolts are tightened using a 1/2” socket
wrench.
II. e - ASSEMBLY OF MODELS RBC400 & RBC400RT:
Double depth roll-in/roll-thru units are shipped as two
separate components which must be attached together
at the jobsite. To accomplish this, first, place the front
and rear cabinets in close proximity to each other being
careful to align the drain from the front of the rear unit
to the drain of the front unit. It will be necessary to level
both units together at this time.
Next, using two pipe clamps, pull the units together (see
figure 3). Install the covers over the gap formed between
the units From inside the cabinets, using the screws
provided, install the breaker strips using the strip as a
template.
-5-
II. RECEIPT INSPECTION
All Traulsen products are factory tested for performance
and are free from defects when shipped. The utmost
care has been taken in crating this product to protect
against damage in transit. All interior fittings have been
carefully secured and the legs or casters are boxed and
strapped inside to prevent damage. Door keys will be
attached to the handle with a nylon strip. The handle is
protected by an easily removable nylon netting.
You should carefully inspect your Traulsen unit for dam-
age during delivery. If damage is detected, you should
save all the crating materials and make note on the
carrier’s Bill Of Lading describing this. A freight claim
should be filed immediately. If damage is subsequently
noted during or immediately after installation, contact
the respective carrier and file a freight claim. Under no
condition may a damaged unit be returned to Traulsen
without first obtaining written permission (return autho-
rization).
III. a - LOCATION:
Select a proper location for your Traulsen unit, away from
extreme heat or cold. Allow enough clearance between
the unit and the side wall so that the door (s) may open
a minimum of 90°.
III. b - PACKAGING:
All Traulsen units are shipped from the factory bolted to
a sturdy wooden pallet and packaged in a durable card-
board container. The carton is attached to the wooden
skid with the use of large staples. These should first be
removed to avoid scratching the unit when lifting off the
crate.
To remove the wooden pallet, first if at all possible, we
suggest that the cabinet remain bolted to the pallet dur-
ing all transportation to the point of final installation.
The bolts can then be removed with a 3/4” socket
wrench. Avoid laying the unit on its front, side or back
for removal of the pallet.
NOTE: Traulsen does not recommend laying the unit
down on its front, side or back. However, if you must
please be certain to allow the unit to remain in an up-
right position afterwards for 24 hours before plugging it
in so that the compressor oils and refrigerant may settle.
III. c - WIRING DIAGRAM:
Refer to the wiring diagram for any service work per-
formed on the unit. Should you require a wiring dia-
gram, please contact Traulsen Service at (800) 825-8220,
and provide the model and serial number of the unit in-
volved.
III. d - INSTALLING LEGS OR CASTERS:
6” high stainless steel legs are supplied standard for
models RBC50 and RBC100. Casters in lieu of legs are
available as an optional accessory for the same mod-
els. These are shipped from the factory packed inside a
cardboard box which is strapped to one of the shelves
(two boxes for model RBC50 which requires either eight
legs or casters). Remove the nylon strap and open the
III. INSTALLATION
III. INSTALLATION (continued)
Fig. 2
Fig. 1
Fig. 3 - Using two pipe
clamps, pull the two units
together and using the
screws provided. Align
the breaker strips as a
template for the screw
pattern inside and
outside the cabinet.