Filter
Top Products
7
Planning the Installation
Self-Rimming Installation Without
Raised Vent
• See page 8 for raised vent installations.
• Only model DR30DI may be installed in a self-rimming
configuration. Self-rimming installations create a “built-in”
look where the trim of the range overlaps the surrounding
countertop. It is also possible, if the cabinets are the right
depth, to self rim the front of the range into the cabinet face,
immediately behind the control panel and door trim. When the
front of the range is self-rimmed, the 3 1/4” side panels are
removed.
• When sliding the range into position, it will stop when the rear
of the side panels or front panel contacts the notches toward
the front of the countertop. The rear of the range trim will
overhang the countertop in back.
Model DR30DI
Range With
H J K
Countertop Self-
Rimmed Only
21”
(53.3 cm)
0” (0 cm) to
3 1/4” (8.3 cm)
0” (0 cm) to
5 3/8” (13.7 cm)
Countertop and
Cabinet Front
Self-Rimmed
1
24 1/4”
(61.6 cm)
NA
0” (0 cm) to
2 1/8” (5.4 cm)
1
Side panels removed
Countertop height for all self-rimming installations:
35 7/16” (90.0 cm) minimum, 37 7/16” (95.1 cm) maximum
Model DR30DI[H] Countertop Self-Rimmed Only,
3 1/4 Inch Side Panels Not Removed
Model DR30DI[H] Countertop and Cabinet Front
Self-Rimmed, 3 1/4 Inch Side Panels Removed
countertop opening
29 1/4” (74.3 cm)
30” (76.2 cm)
cabinet opening
below countertop
below countertop
To cabinet face
Notch countertop
overhang to width of
cabinets below
1/4” min.* (6 mm)
countertop
overhang
10” min.
(25.4 cm)
both sides
To countertop
front
H
J
K
Combustible side
wall above range
Rear wall or other
vertical surface **
** Any vertical surfaces behind the range must be non-combustible
unless countertop overhang exceeds 2 3/4” (7.0 cm).
Countertop height: min: 35 7/16” (90.0 cm) max: 37 7/16” (95.1 cm)
* When increasing overhang, increase dimension H by same amount.
Rear wall or other
vertical surface **
** Any vertical surfaces behind the range must be non-combustible
unless countertop overhang exceeds 2 3/4” (7.0 cm).
Countertop height: min: 35 7/16” (90.0 cm) max: 37 7/16” (95.1 cm)
* When increasing overhang, increase dimension H by same amount.
countertop and
cabinet opening
Notch countertop to
29 1/4” (74.3 cm)
below countertop
Cabinet face
30” (76.2 cm)
1/4” min.* (6 mm)
countertop
overhang
10” min.
(25.4 cm)
both sides
To countertop
front
H
K
Combustible side
wall above range
Cabinet face
Countertop
Back of control
panel and trim
behind door
rest against
cabinet face
DR30DI[H] range
1/4” min. (6.4 mm)
flat countertop min.
Range side
panels removed
Range trim resting
on countertop
See Top View for required distance
to vertical surfaces
H
Back of cutout
Countertop
DR30DI[H] range
H
1/4” min. (6.4 mm)
flat countertop min.
Range trim resting
on countertop
See Top View for required distance
to vertical surfaces
Cabinet face
Back of
cutout
Back of
control
panel
3 1/4 inch
side panel
Top View Top View
Side ViewSide View