Filter
Top Products
C—6 16021875 Rev. 0 ©2003 Maytag Appliances Company
Self-Cleaning
• A small amount of smoke is normal when cleaning.
Excessive smoke may indicate too much food
residue has been left in oven or a faulty gasket.
• Oven should be cleaned before it gets too dirty. Wipe
up large spills before self-cleaning.
• Do not use self-cleaning cycle if oven light cover is
not properly in place.
• Oven light will not work during clean cycle.
1. Remove oven racks and all cooking utensils from
oven. Clean excess spills from oven interior.
2. Press CLEAN pad.
3. Press
+
or
-
until desired cleaning time is
displayed. Clean can be set from 2 to 4 hours.
Recommended clean time is 3 hours.
• Oven will begin to clean automatically. “CLEAN”,
“LOCK”, and “ON” will light in display. As oven
door locks and unlocks “LOCK” will flash in
display. When door is locked, “LOCK” will remain
in display. When cleaning cycle has elapsed,
oven will automatically turn off. End-of-cycle
signal will not sound.
CAUTION
!
To avoid risk of personal injury do not touch oven
vents or areas around vents during self-cleaning.
These areas can become hot enough to cause burns.
To avoid risk of damage to automatic locking system,
do not try to force oven door open when “LOCK” is
flashing in display.
• When oven has cooled to a safe temperature,
“LOCK” will disappear from display and door can
be opened. "LOCK" will flash in display while
unlocking.
Interrupt Self-Cleaning Cycle
1. Pres OVEN CANCEL pad.
2. When oven has cooled to a safe temperature, lock
will disappear from display and door can be opened.
Delayed Self-Cleaning
1. Remove oven racks and all cooking utensils from
oven. Clean excess spills from oven interior.
2. Press CLEAN pad.
3. Press
+
or
-
until desired cleaning time is
displayed.
4. Press STOP TIME pad.
5. Press
+
or
-
until desired stopping time is
displayed. A starting time will automatically be
calculated based on amount of cleaning time and
stop time.
• “DELAY”, “CLEAN”, and “LOCK” will light in
display. As oven door locks and unlocks “LOCK”
will flash in display. Oven will begin to clean at
preset time and “ON” will light in display. When
cycle is complete oven will automatically turn off.
CAUTION
!
To avoid risk of personal injury do not touch oven
vents or areas around vents during self-cleaning.
These areas can become hot enough to cause burns.
To avoid risk of damage to automatic locking system,
do not try to force oven door open when “LOCK” is
flashing in display.
• When oven has cooled to safe temperature,
“LOCK” will disappear from display and door can
be opened.
Canceling Self-Cleaning Cycle
1. Press OVEN CANCEL pad.
2. When oven has cooled to a safe temperature,
“LOCK” will disappear from display and door can be
opened.
Adjusting Oven Temperature
Oven temperature has been factory calibrated and
tested. In unlikely event that oven consistently
overcooks or undercooks food, oven temperature can
be adjusted.
1. Press BAKE pad.
2. Press
+
o
until an oven temperature greater than
500°F shows in display.
3. Immediately Press and hold BAKE pad until "00"
appears in display, approximately 5 seconds.
4. To decrease oven temperature (for cooler oven),
press
r
-
until negative numbers appear.
Oven can be adjusted from -05° to -35° lower. To
avoid over-adjusting oven move temperature -5°
each time.
5. To increase oven temperature (for a warmer oven)
press
+
o
until positive number’s appear. Oven can
be set from 05° to 35° higher. To avoid over
adjusting oven, move temperature 5° each time.
6. Press OVEN CANCEL pad. Temperature adjustment
will be retained even through a power failure.
Programming Instructions—ERC for AOCS3040