Filter
Top Products
28
TroubleshootingBefore Use Operation Cleaning
How to cleanBefore cleaning
Step
Step
2
Step
Step
1
Remove the power plug
Wait at least 10 minutes before reinserting the power plug
into the socket.
If you insert the plug immediately, the mechanism will not
function.
• Wipe with a soft cloth soaked in warm water, or remove and rinse
(Wipe the control panel with a soft, dry cloth.)
•
For stubborn dirt, wipe using water mixed with a weak concentration of kitchen
In particular, be sure to wipe off oily dirt because leaving it may damage the
Do not use insecticide spray,alkaline or low alkaline kitchen
powdered soap, alcohol, benzene, thinner, oil, acid, scrubbers,
Doing so may cause the plastic parts (such as the door
or damage or rust the doors or painted surfaces.
Push in and
lift up.
c
Set the left and right levers to
the "Lock" position.
d
Hold the front of the Revolving
Shelf with both hands, and
while slightly lifting up the rear,
push the Revolving Shelf to the
rear. (Guide the rear of the shelf
to get on the left and right rails.)
e
Lift the front of the Revolving
Shelf, and remove from the
refrigerator. (Pass it on the top
of the left and right rails.)
c
Push up the 3 tabs on the rear of the tray
with your fi nger.
d
Lift up the rear of the tray until the 3
front tabs and the 2 side tabs disengage.
* There is a risk of the tray falling.
Move it slowly.
e
Pull out with both hands.
c
Set the lever to the "Lock" position.
d
Hold the stopper knob
in the middle of the
Revolving Shelf, and
remove the stopper
by turning it in the
direction of the arrow.
e
Insert your hand
from the center of the
Revolving Shelf, and
lift up the tray.
*There is a risk of the tray falling.
Move it slowly.
f
Pull out with both hands.
c
Make sure that the lever
is on the right side.
d
Make sure that the 4 metal stoppers are
fi tted, and place the shelf lightly so that
the 4 supports are aligned with the 4 metal
stoppers.
e
Push in each of the 4 supports in turn from
above. (A clicking sound is made.)
f
Move the lever to the left and right and
check that the AUTO Shelf is kept level
when moved up and down. (
If the shelf is
not kept level, remove the AUTO Shelf
and repeat steps
c
to
f
.)
c
Make sure that the levers are in the
"Lock" position.
d
Place the Revolving Shelf in the
refrigerator, put it on the left and right
rails, and pass it on the rails to the rear.
e
While passing the Revolving Shelf
through the grooves of the left and
right rails and pulling it to the front,
lower the rear of the Revolving Shelf.
(When pulling the Revolving Shelf to
the front, make sure that it stops in the
grooves of the rails.)
Shelf removal
Shelf removal
Shelf installation
Shelf installation
Tray removal
Tray removal
c
Move the lever to the right end.
d
Strongly push up each support,
one by one. (4 locations.)
(A clicking
sound is made
when the support
disengages.
)
If the supports are fi rmly set
and diffi cult to disengage, tilt
the inner tabs to the inner side.
e
Remove from the refrigerator.
When installing the tray, position the tray in the
direction shown in the fi gure. Installing in other
directions will result in incorrect installation,
and the part may fall out.
Failure to unplug
may result in an
electric shock.
Warning
Removing and Cleaning
the Parts
Two-way fl exishelf
Revolving Shelf
AUTO Shelf
(Do not disassemble the AUTO Shelf, or use chemicals such as grease to clean it. Doing so may cause a malfunction.)
Stopper
Lever
Lever
Lever
Lever