Filter
Top Products
Continued from front matter. . .
7.C.NL.07.31.00.R1.M.CW6FC
Warranty (cont’d)
Agilent does not warrant that
the operation of Agilent
products will be uninterrupted
or error free. If Agilent is
unable, within a reasonable
time, to repair or replace any
product to a condition as
warranted, customer will be
entitled to a refund of the
purchase price upon prompt
return of the product.
Agilent products may contain
remanufactured parts
equivalent to new in
performance or may have been
subjected to incidental use.
The warranty period begins on
the date of delivery or on the
date of installation if installed
by Agilent. If customer
schedules or delays Agilent
installation more than 30 days
after delivery, warranty begins
on the 31st day from delivery.
Warranty does not apply to
defects resulting from
(a) improper or inadequate
maintenance or calibration,
(b) software, interfacing, parts
or supplies not supplied by
Agilent, (c) unauthorized
modification or misuse,
(d) operation outside of the
published environmental
specifications for the product, or
(e) improper site preparation or
maintenance.
TO THE EXTENT ALLOWED
BY LOCAL LAW, THE ABOVE
WARRANTIES ARE
EXCLUSIVE AND NO OTHER
WARRANTY OR CONDITION,
WHETHER WRITTEN OR
ORAL, IS EXPRESSED OR
IMPLIED AND AGILENT
SPECIFICALLY DISCLAIMS
ANY IMPLIED WARRANTIES
OR CONDITIONS OF
MERCHANTABILITY,
SATISFACTORY QUALITY,
AND FITNESS FOR A
PARTICULAR PURPOSE.
Agilent will be liable for damage
to tangible property per incident
up to the greater of $300,000 or
the actual amount paid for the
product that is the subject of the
claim, and for damages for
bodily injury or death, to the
extent that all such damages
are determined by a court of
competent jurisdiction to have
been directly caused by a
defective Agilent product.
TO THE EXTENT ALLOWED
BY LOCAL LAW, THE
REMEDIES IN THIS
WARRANTY STATEMENT
ARE CUSTOMER’S SOLE AND
EXCLUSIVE REMEDIES.
EXCEPT AS INDICATED
ABOVE, IN NO EVENT WILL
AGILENT OR ITS SUPPLIERS
BE LIABLE FOR LOSS OF
DATA OR FOR DIRECT,
SPECIAL, INCIDENTAL,
CONSEQUENTIAL
(INCLUDING LOST PROFIT
OR DATA), OR OTHER
DAMAGE, WHETHER BASED
IN CONTRACT, TORT, OR
OTHERWISE.
For consumer transactions
in Australia and New
Zealand: the warranty terms
contained in this statement,
except to the extent lawfully
permitted, do not exclude,
restrict or modify and are in
addition to the mandatory
statutory rights applicable
to the sale of this product to
you.
Assistance
Product maintenance
agreements and other customer
assistance agreements are
available for Agilent products.
For any assistance, contact your
nearest Agilent Sales and
Service Office.
Safety Considerations
(cont’d)
WARNING
INSTRUCTIONS FOR
ADJUSTMENTS WHILE
COVERS ARE REMOVED
AND FOR SERVICING ARE
FOR USE BY SERVICE-
TRAINED PERSONNEL
ONLY. TO AVOID
DANGEROUS ELECTRIC
SHOCK, DO NOT PERFORM
SUCH ADJUSTMENTS OR
SERVICING UNLESS
QUALIFIED TO DO SO.
WARNING
ANY INTERRUPTION OF THE
PROTECTIVE GROUNDING
CONDUCTOR (INSIDE OR
OUTSIDE THE PRODUCT’S
CIRCUITRY) OR
DISCONNECTING THE
PROTECTIVE EARTH
TERMINAL WILL CAUSE A
POTENTIAL SHOCK
HAZARD THAT COULD
RESULT IN PERSONAL
INJURY. (GROUNDING ONE
CONDUCTOR OF A TWO
CONDUCTOR OUTLET IS
NOT SUFFICIENT
PROTECTION.)
Whenever it is likely that the
protection has been impaired,
the instrument must be made
inoperative and be secured
against any unintended
operation.
If this instrument is to be
energized via an
autotransformer (for voltage
reduction), make sure the
common terminal is connected
to the earthed pole terminal
(neutral) of the power source.
Instructions for adjustments
while covers are removed and
for servicing are for use by
trained personnel only. To avoid
dangerous electric shock, do not
perform such adjustments or
servicing unless qualified to do so.
For continued protection
against fire, replace the line
fuse(s) with fuses of the same
current rating and type (for
example, normal blow, time
delay). Do not use repaired
fuses or short-circuited
fuseholders.
Acoustic Noise Emissions
LpA<47 dB at operator position,
at normal operation, tested per
EN 27779. All data are the
results from type test.
Geräuschemission
LpA<47 dB am Arbeits
platz, normaler Betrieb, geprüft
nach EN 27779.
Die Angagen beruhen auf
Ergebnissen von
Typenprüfungen.
Electrostatic Discharge
Immunity Testing
When the product is tested with
8kV AD, 4kV CD and 4kV ID
according to IEC801-2, a system
error may occur that may affect
measurement data made during
these disturbances. After these
occurrences, the system self-
recovers without user
intervention.