Filter
Top Products
29
To scroll to the next user option press the button.
You are now in the end of cycle beeps setting of the preference options menu.
To change the setting press the button, all LED’s on = end of cycle beeps on, all LED’s o = end of cycle beeps
o.
To save or quit the menu, press and hold the button until a beeps sounds and the control panel reverts to
showing the wash program currently selected.
* This option is disabled on models without a water softener, the option will appear in the sequence of options
but cannot be adjusted. (refer to previous page)
After the wash
Dos and don’ts of loading
Preference options
The dishwasher will beep six times to indicate the end of the wash program.
You may notice the following noises at the end of the wash. These are all part of normal operation:
In double models, both drawers may be draining simultaneously.
The drying fan may continue to run after a wash program has finished for a set time. The fan assists with drying and uses
negligible amounts of energy.
For best drying results, we recommend unloading the dishes once they have cooled.
You can change the setting of these options to suit your preferences or circumstances. We recommend selecting the most suitable
settings before you start using your dishwasher.
How to change the setting of an option
1
CHECK & OPEN
Check that there is no wash underway, then open the drawer.
2
ENTER MENU & SCROLL TO OPTION
To enter the menu: press first with one finger, then with another finger, hold both until one long beep sounds, then
release.
You are now in the Rinse aid option of the preference options menu.
If you want to change the Rinse aid setting, go to step 3 now.
If you want to change the setting of another option, you will need to scroll to that option first.
To scroll to the next option: press
. To know which option you’re in, keep track of the sequence of options using the table below.
When you have scrolled to the end of the sequence, it will start again with Rinse aid (after the lower tone).
3
CHANGE SETTING
Press to change the setting within an option. For example, to change the Rinse aid setting from 4 (factory default) to 2, you need
to press
3 times.
4
SAVE SETTING & QUIT MENU
Press and hold until a beep sounds and the control panel reverts to showing the wash program currently selected.
*This option is disabled on models without water softener. It appears in the sequence of options but cannot be adjusted.
A neatly arranged load with evenly
spaced dishes helps wash performance.
Sharp or pointed items must be placed
horizontally or with sharp edges/points
facing down to avoid risk of injury.
Overcrowding reduces wash
performance.
Protruding items will stop the
internal lid of the drawer from
sealing properly, which could result
in a service call.
Ensure there is enough space between
plates. Mix spoons, knives and forks
within the cutlery basket to prevent
them from nesting.
If plates and cutlery are nesting,
they are less likely to be cleaned
well.
Ensure that water reaches all items on
the adjustable racks.
Dishware is blocking water from
reaching items on the adjustable
racks.
Option Rinse aid Water softener* Beeps at end of wash
What does it do?
Regulates the amount of rinse aid
dispensed. Reduce this setting if there is
excess foam after a wash. Increase this
setting if dishes are wet or streaky after
a wash.
Refer to the ‘Water softener’
section of the ‘User guide’ for
details.
Your dishwasher is factory-set to beep
six times at the end of a wash. You can
turn this setting off.
Option Rinse aid Water softener* Beeps at end of wash
Possible settings
1 to 5 0 to 5 On/Off
Example
4 indicators lit = setting is 4
3 indicators lit = setting is 3
On
Off
For more info
For detailed information on the
features of your dishwasher
For warranty information
If you…
have any questions or comments
need a Fisher & Paykel authorized
technician to service your product
need replacement parts or accessories
want to register your product
see your ‘User guide’
see your ‘Service and warranty’ booklet
see your ‘Service and warranty’ booklet or contact us
NZ
toll-free, 24/7
0800 372 273 www.fisherpaykel.co.nz
AU
toll-free, 24/7
1300 650 590 www.fisherpaykel.com.au
USA
toll-free, 24/7
1 888 936 7872 www.fisherpaykel.com
CA
toll-free, 24/7
1 888 936 7872 www.fisherpaykel.ca
590194A 10.11
NZ, AU, US, CA
Secondary
Panel
After the wash
Dos and don’ts of loading
Preference options
Closed Drawer autolock using the remote control
The dishwasher will beep six times to indicate the end of the wash program.
You may notice the following noises at the end of the wash. These are all part of normal operation:
In double models, both drawers may be draining simultaneously.
The drying fan may continue to run after a wash program has finished for a set time. The fan assists with drying and uses
negligible amounts of energy.
For best drying results, we recommend unloading the dishes once they have cooled.
You can change the setting of these options to suit your preferences or circumstances. We recommend selecting the most suitable
settings before you start using your dishwasher.
The Closed Drawer autolock feature will lock the dishwasher when the drawer is closed. To enable this feature - with the drawer closed
(and no wash program or delay start is active), press and hold
on the remote for 6 seconds until you hear a sequence of 4 beeps
together. Ignore any beeps prior to the 6 seconds. The drawer is now locked. To unlock, press
once. You will hear a sequence of 4 beeps
together. The drawer is now unlocked.
On double products, the drawers must be locked independently.
If the power to the dishwasher is disconnected, the drawer will remain locked.
Note: this feature is highly recommended if the dishwasher is to be used in motor homes.
How to change the setting of an option
1
CHECK & OPEN
Check that there is no wash underway, then open the drawer.
2
ENTER MENU & SCROLL TO OPTION
To enter the menu: press first with one finger, then with another finger, hold both until one long beep sounds, then
release.
You are now in the Rinse aid option of the preference options menu.
If you want to change the Rinse aid setting, go to step 3 now.
If you want to change the setting of another option, you will need to scroll to that option first.
To scroll to the next option: press
. To know which option you’re in, keep track of the sequence of options using the table below.
When you have scrolled to the end of the sequence, it will start again with Rinse aid (after the lower tone).
3
CHANGE SETTING
Press to change the setting within an option. For example, to change the Rinse aid setting from 4 (factory default) to 2, you need
to press
3 times.
4
SAVE SETTING & QUIT MENU
Press and hold until a beep sounds and the control panel reverts to showing the wash program currently selected.
*This option is disabled on models without water softener. It appears in the sequence of options but cannot be adjusted.
A neatly arranged load with evenly
spaced dishes helps wash performance.
Sharp or pointed items must be placed
horizontally or with sharp edges/points
facing down to avoid risk of injury.
Overcrowding reduces wash
performance.
Protruding items will stop the
internal lid of the drawer from
sealing properly, which could result
in a service call.
Ensure there is enough space between
plates. Mix spoons, knives and forks
within the cutlery basket to prevent
them from nesting.
If plates and cutlery are nesting,
they are less likely to be cleaned
well.
Ensure that water reaches all items on
the adjustable racks.
Dishware is blocking water from
reaching items on the adjustable
racks.
Option Rinse aid Water softener* Beeps at end of wash
What does it do?
Regulates the amount of rinse aid
dispensed. Reduce this setting if there is
excess foam after a wash. Increase this
setting if dishes are wet or streaky after
a wash.
Refer to the ‘Water softener’
section of the ‘User guide’ for
details.
Your dishwasher is factory-set to beep
six times at the end of a wash. You can
turn this setting off.
Option Rinse aid Water softener* Beeps at end of wash
Possible settings
1 to 5 0 to 5 On/Off
Example
4 indicators lit = setting is 4
3 indicators lit = setting is 3
On
Off
For more info
For detailed information on the
features of your dishwasher
For warranty information
If you…
have any questions or comments
need a Fisher & Paykel authorized
technician to service your product
need replacement parts or accessories
want to register your product
see your ‘User guide’
see your ‘Service and warranty’ booklet
see your ‘Service and warranty’ booklet or contact us
NZ
toll-free, 24/7
0800 372 273 www.fisherpaykel.co.nz
AU
toll-free, 24/7
1300 650 590 www.fisherpaykel.com.au
USA
toll-free, 24/7
1 888 936 7872 www.fisherpaykel.com
CA
toll-free, 24/7
1 888 936 7872 www.fisherpaykel.ca
590194B 05.12