■ max-graft-retries < 1 to 10 > -- Set the maximum number of times this router will resend
a Graft on this interface (p. 734)
■ override-interval < 500 to 6000 > -- Set the value inserted into the Override Interval field
of a LAN Prune Delay option on this interface (p. 739)
■ propagation-delay < 250 to 2000 > -- Set the value inserted into the LAN Prune Delay field
of a LAN Prune Delay option on this interface (p. 743)
■ ttl-threshold < 0 to 255 > -- Set the Time To Live in a PIM-DM State Refresh message at
which it is not forwarded on this interface (p. 749)
■ pim-sparse -- Enable/disable/configure PIM-SM protocol on the VLAN interface (p. 740)
■ dr-priority -- Set the priority value to use on the interface in the Designated Router election
process (p. 722)
■ hello-delay < 0 to 5 > -- Set the maximum time before a triggered PIM Hello message is
transmitted on this interface (p. 725)
■ hello-interval < 5 to 300 > -- Set the frequency at which PIM Hello messages are transmitted
on this interface (p. 725)
■ ip-addr -- Set the source IP address for the PIM-SM packets sent out on this interface (p.
729)
■ any -- Dynamically determine IP address. (p. 716)
■ ip-addr -- Specify IP address. (IP-ADDR) (p. 729)
■ lan-prune-delay -- Turn on/off the LAN Prune Delay Option on this interface (p. 733)
■ nbr-timeout < 60 to 8000 > -- Set the neighbour loss time interval for this interface (p. 737)
■ override-interval < 500 to 6000 > -- Set the value inserted into the Override Interval field
of a LAN Prune Delay option on this interface (p. 739)
■ propagation-delay < 250 to 2000 > -- Set the value inserted into the LAN Prune Delay field
of a LAN Prune Delay option on this interface (p. 743)
■ proxy-arp -- Enable/disable proxy ARP (p. 744)
■ rip -- Enable/disable/configure Routing Internet Protocol (RIP) on the VLAN interface (p. 746)
■ all -- Process the request for all IP addresses. (p. 715)
■ authentication-key -- Set RIP authentication key (maximum 16 characters). (p. 717)
■ auth-key-text -- Set RIP authentication key (maximum 16 characters). (OCTET-STR)
(p. 719)
■ authentication-type < none | text > -- Set authentication type used on this interface. (p.
718)
■ metric < 1 to 15 > -- Set metric for this interface. (p. 734)
■ poison-reverse -- Enable/disable poison reverse on this interface. (p. 741)
■ receive < V1-only | V2-only | V1-or-V2 | ... > -- Define RIP version for incoming packets.
(p. 745)
■ rip-compatible < V1-only | V2-only | V1-or-V2 > -- Define RIP version for incoming and
outgoing packets. (p. 747)
■ send < disabled | V1-only | V1-compatible-V2 | ... > -- Define RIP version for outgoing
packets. (p. 747)
■ authentication-key -- Set RIP authentication key (maximum 16 characters). (p. 717)
■ auth-key-text -- Set RIP authentication key (maximum 16 characters). (OCTET-STR) (p.
719)
■ authentication-type < none | text > -- Set authentication type used on this interface. (p. 718)
■ ip-addr -- Specify the IP address the request is for. (IP-ADDR) (p. 729)
■ authentication-key -- Set RIP authentication key (maximum 16 characters). (p. 717)
■ auth-key-text -- Set RIP authentication key (maximum 16 characters). (OCTET-STR)
(p. 719)
■ authentication-type < none | text > -- Set authentication type used on this interface. (p.
718)
■ metric < 1 to 15 > -- Set metric for this interface. (p. 734)
■ poison-reverse -- Enable/disable poison reverse on this interface. (p. 741)
709© 2009 Hewlett-Packard Development Company, L.P.
vlanCommand Line Interface Reference Guide
