Filter
Top Products
© 1998 Maytag Corporation
16008373-01 SECTION 1. GENERAL INFORMATION 1-4
Figure 1-6
SPECIFICATIONS
Plug power cord into a properly grounded 120
volt AC-approved electrical service. This
must be protected by a dedicated 15 amp fuse
or circuit breaker.
All grounding and wiring should be performed
in accordance with national and local codes.
USE OF ADAPTERS IS NOT RECOMMENDED.
CAPACITY 3.1 Cubic Feet
ELECTRICAL 120 volts, 60 Hz; Requires 15 amp circuit breaker or fused electrical
supply. Power cord must be connected to a properly grounded and
polarized outlet.
MOTOR Switched Reluctance Motor controlled by a microprocessor motor
control board. Motor pulley ratio (motor to spinner RPM) 14 to 1.
POWER USAGE Motor Input: During Wash Tumble - 150 Watts
During Rinse Tumble - 175 Watts
Top Spin - 800 Watts
(Wattage readings taken with no clothes in spinner.)
TUMBLER SPEED Wash Tumble 47-51 RPM
Rinse Tumble 47-51 RPM
High Speed Spin 800 RPM (± 50 RPM based upon optimum
spin performance.)
WATER USAGE Water pressure should be 20-120 p.s.i. (1.06-8.44 kg/cm) at inlet hose
connection. Total water usage is approximately 25 gallons; varies with
clothes load. Water fill in the spin basket with no clothes, measured
near the rear seam of the spin basket.
WASH LEVEL 3-4 inches
RINSE LEVEL 4-5 inches
HOSE LENGTHS Four-foot inlet hoses with inlet washers and attaches to water valve.
Drain hose attaches to pump and will accommodate 36" drain stand
pipe.
DIMENSIONS Cabinet dimensions: 27" (68.58cm) W x 27 ½” (69.85cm) D x 36"
(91.44cm )H.
WEIGHT (Approx.) Uncartoned 190lb. (86kg.) Approx.
Crated 200lb. (91kg). Approx.
SCREW & BOLT TORQU ES Bolt, Counter Weight 7in. lbs. (± 3in.lbs)
Bolt, Spin Pulley 30in. lbs (± 3in. lbs)
Bolt, Belt Adjuster 90in. lbs (± 10in. lbs)
Screw, Front Baffle 25in. lbs (± 3in. lbs)
Screw, Rear Baffle 18.5in. lbs (± 3in. lbs)
Clamp, Hoses 15+ in. lbs
Nuts, Spinner Support 18in. lbs (± 3in. lbs)
Nuts, Suspension Struts 7in. lbs (± 3in. lbs)
CAPACITY 3.1 Cubic Feet
ELECTRICAL 120 volts, 60 Hz; Requires 15 amp circuit breaker or fused electrical
supply. Power cord must be connected to a properly grounded and
polarized outlet.
MOTOR Switched Reluctance Motor controlled by a microprocessor motor
control board. Motor pulley ratio (motor to spinner RPM) 14 to 1.
POWER USAGE Motor Input: During Wash Tumble - 150 Watts
During Rinse Tumble - 175 Watts
Top Spin - 800 Watts
(Wattage readings taken with no clothes in spinner.)
TUMBLER SPEED Wash Tumble 47-51 RPM
Rinse Tumble 47-51 RPM
High Speed Spin 800 RPM (± 50 RPM based upon optimum
spin performance.)
WATER USAGE Water pressure should be 20-120 p.s.i. (1.06-8.44 kg/cm) at inlet hose
connection. Total water usage is approximately 25 gallons; varies with
clothes load. Water fill in the spin basket with no clothes, measured
near the rear seam of the spin basket.
WASH LEVEL 3-4 inches
RINSE LEVEL 4-5 inches
HOSE LENGTHS Four-foot inlet hoses with inlet washers and attaches to water valve.
Drain hose attaches to pump and will accommodate 36" drain stand
pipe.
DIMENSIONS Cabinet dimensions: 27" (68.58cm) W x 27 ½” (69.85cm) D x 36"
(91.44cm )H.
WEIGHT (Approx.) Uncartoned 190lb. (86kg.) Approx.
Crated 200lb. (91kg). Approx.
SCREW & BOLT TORQU ES Bolt, Counter Weight 7in. lbs. (± 3in.lbs)
Bolt, Spin Pulley 30in. lbs (± 3in. lbs)
Bolt, Belt Adjuster 90in. lbs (± 10in. lbs)
Screw, Front Baffle 25in. lbs (± 3in. lbs)
Screw, Rear Baffle 18.5in. lbs (± 3in. lbs)
Clamp, Hoses 15+ in. lbs
Nuts, Spinner Support 18in. lbs (± 3in. lbs)
Nuts, Suspension Struts 7in. lbs (± 3in. lbs)