Support User Manuals

Agilent Technologies Agilent 86120C Ventilation Hood User Manual

Open as PDF

of 294

3-45

Programming

Lists of Commands

:CALCulate3:DELTa:REFerence[:WAVelength] Selects the signal to be used as the reference for the

DELTa calculations.

I

:CALCulate3:DELTa:REFerence:WNUMber Selects the signal to be used as the reference for the

DELTa calculations.

I

:CALCulate3:DELTa:WAVelength[:STATe] Turns the delta wavelength measurement mode on and off. I

:CALCulate3:DELTa:WPOWer[:STATe] Turns the delta wavelength and power measurement mode

on and off.

I

:CALCulate3:DRIFt:DIFFerence[:STATe] Sets the drift calculation to subtract the minimum values

measured from the maximum values measured.

I

:CALCulate3:DRIFt:MAXimum[:STATe] Sets the drift calculation to return the maximum power

(frequency) values measured.

I

:CALCulate3:DRIFt:MINimum[:STATe] Sets the drift calculation to return the minimum power

(frequency) values measured.

I

:CALCulate3:DRIFt:PRESet Turns off all the drift states for DIFFerence, MAXimum,

MINimum, and REFerence.

I

:CALCulate3:DRIFt:REFerence:RESet Places the current list of signals into the reference list. I

:CALCulate3:DRIFt:REFerence[:STATe] Turns the drift state on and off so that CALC3:DATA? will

return the reference signal list.

I

:CALCulate3:DRIFt[:STATe] Turns the drift measurement calculation on and off. I

:CALCulate3:FPERot[:STATe] Turns the Fabry-Perot measurement mode on and off. I

:CALCulate3:FPERot:MEAN:[WAVelength]? Queries the mean wavelength of the selected modes. I

:CALCulate3:FPERot:MEAN:FREQuency? Queries the mean frequency of the selected modes. I

:CALCulate3:FPERot:MEAN:WNUMber? Queries the mean wavenumber of the selected modes. I

:CALCulate3:FPERot:PEAK:[WAVelength]? Queries the peak wavelength of the selected modes. I

:CALCulate3:FPERot:PEAK:FREQuency? Queries the peak frequency of the selected modes. I

:CALCulate3:FPERot:PEAK:WNUMber? Queries the peak wavenumber of the selected modes. I

:CALCulate3:FPERot:PEAK:POWer? Queries the peak power of the selected modes. I

:CALCulate3:FPERot:FWHM:[WAVelength]? Queries full width half-max wavelength of selected modes. I

:CALCulate3:FPERot:FWHM:FREQuency? Queries full width half-max frequency of selected modes. I

:CALCulate3:FPERot:FWHM:WNUMber? Queries full width half-max wavenumber of selected

modes.

I

:CALCulate3:FPERot:MODE:SPACing:[WAVelengt

h]?

Queries the mode spacing wavelength of the selected

modes.

I

:CALCulate3:FPERot:MODE:SPACing:FREQuenc

y?

Queries the mode spacing frequency of the selected

modes.

I

:CALCulate3:FPERot:MODE:SPACing:WNUMbe

r?

Queries the mode spacing wavenumber of the selected

modes.

I

Table 3-10. Programming Commands (3 of 5)

Command Description Code

Codes: S indicates a standard SCPI command. I indicates an instrument specific command.

previous next