Mitsubishi Electronics SW2D5C-GTWK2-E Frozen Dessert Maker User Manual


 
5.2 Communication Setup
5.2.1 Communication setup dialog box
5 - 3
1
OVERVIEW
2
SYSTEM
CONFIGURATION
3
SPECIFICATIONS
4
SCREEN
CONFIGURATION
5
OPERATING
METHOD
6
FUNCTIONS
7
INTERNAL DEVICE
INTERFACE
FUNCTION
8
TROUBLESHOOTING
APPENDICES
(Continued to next page)
Item Description
Connection
Select the connection method of GT SoftGOT1000.
CPU : Select this option for direct connection to CPU via the RS-232 cable.
USB : Select this option for direct connection to CPU via the USB cable.
C24 : Select this option when computer link connection is used.
NET/H : Select this option when using the MELSECNET/H interface board.
Select "NET/H" when using the GT SoftGOT1000 in MELSECNET/10 mode.
CC IE Control : Select this option when using the CC-Link IE controller network interface board.
Ethernet : Select this option when Ethernet connection is used.
BUS : Select [BUS] when the bus connection is used.
-
*1
If CPU/USB/C24/NET/H/CC IE Control/Ethernet is selected as the connection method, specify the connection
destination.
When CPU/USB is selected: Selects the type of CPU to be connected.
When C24 is selected : Selects the type of computer link module or serial communication module to be
connected.
When NET/H/CC IE Control is selected
: Select the interface board mounted on the personal computer to be used.
When Ethernet is selected : Select the model of a programmable controller to be connected.
CPU/C24 When selecting CPU/C24 in the connection method, set the following items.
Comm. port
Choose the communication port on the personal computer side.
COM1 to COM6
Baud rate
Set the transmission speed to/from the CPU.
Set the baud rate to be used.
When connecting a QnA/A series computer link, set the same baud rate as the one set in the computer link/serial
communication module to be used.
For connection with the FXCPU, select the baud rate supported by the connected FXCPU.
When the set baud rate is not supported, communication is made at 9.6kbps.
When selecting a transmission speed that is not supported by OMRON SYSMAC, a communication error occurs.
Timeout
Set the timeout period and retry count.
Depending on the settings on the [Connection] menu, some items cannot be set.
Host
Set the timeout period for host monitor.
"3" to "90" (seconds)
Other
Set the timeout period for other station monitor.
"3" to "90" (seconds)
Retry
Set the number of retries.
"0" to "10" (times)
CC IE Control When selecting [CC IE Control] in the connection method, set the following item.
Monitor Speed
Set the monitor speed for CC-Link IE controller network.
[High], [Normal], [Low]
Ethernet When selecting "Ethernet" in the connection method, set the following items.
NET No.
Set the network number of GT SoftGOT1000.
"1" to "239"
PC No.
Set the station number of GT SoftGOT1000.
The station number must be different from the PLC No. of the Ethernet module to be monitored. "1" to "64"
Port No.
*2
Set the port number of GT SoftGOT1000.
"1024" to "65535"
Wait Time
Set the transmission wait time to reduce the load on the network and target PLC.
"0" to "10000" (x 10 ms)
Option Set the options when selecting [YASKAWA] from [CPU] on the selecting method.
Host Add.
Specify the host address (the station number of a programmable controller to which connects GT SoftGOT1000)
within the connection network.
[1] to [31]
Wait Time
Set the transmission time to reduce the loads of a network and a target programmable controller.
[0] to [30] (x 10ms)