Filter
Top Products
Central Office Calls, Answering
212 ◆ Features Aspire Software Manual
➻ 14-05-01 : Trunk Groups
For Universal Answer, assign trunks to trunk groups then go to Program 14-06 below to set up
Trunk Group Routing.
➪ Aspire S Trunk Groups: 1-8
➪ Aspire Trunk Groups: 1-100
➻ 14-06-01 : Trunk Group Routing
For Universal Answer, set up trunk routes and then go to Program 23-03 below to assign the
trunk routes to extensions. An extension user can use Universal Answer to answer a call if the
ringing trunk is in its assigned route.
➪ Aspire S Trunk Group Routes: 1-8
➪ Aspire Trunk Group Routes: 1-100
➻ 14-07-01 : Trunk Access Map Setup
Set up the Trunk Access Maps. This sets the access options for trunks. Ring Group program-
ming overrides Access Map programming.
➪ Aspire S: Trunk Access Maps 1-8
➪ Aspire: Trunk Access Maps 1-200
➻ 14-01-27 : Basic Trunk Data Setup - Caller ID Refuse Setup
This program defines if the system rejects a trunk call (0=does not reject the call, 1 = rejects
the call) and plays a VRS message based on the Caller ID information received. This option is
set on a per trunk basis.
➪ Aspire S Trunks: 1-8
➪ Aspire M/L/XL Trunks: 1-200
➻ 15-01-05 : Basic Extension Data Setup - Restriction for Outgoing Disable on Incoming
Line
Enable (1) or disable (0) supervised dial detection for an extension.
➻ 15-02-01 : Multi-Line Telephone Basic Data Setup
Select the language which should be used on a keyset’s display (0 = Japanese, 1 = English, 2 =
German, 3 = French, 4 = Italian, 5 = Spanish, 6 = Dutch, 7 = Portuguese, 8 = Norwegian, 9 =
Danish).
➻ 15-02-02 : Multi-Line Telephone Basic Data Setup - Trunk Ring Tone
Trunks ring extensions according to the Ring Tone Range selected in 22-03 and the settings
made with either Service Code 820 or Program 15-02-02. Also see Program 22-03.
➻ 15-02-22 : Multi-Line Telephone Basic Data Setup, Multiple Incoming From Intercom
and Trunk
When this option is set to ‘0’ (disabled), incoming calls to an extension will indicate on any
Hotline keys for that extension as solid (busy). When this option is set to ‘1’ (enabled), lamp-
ing is determined by the setting of Program 22-01-01 Incoming Call Priority. If set to trunk
priority (1), the Hotline key will lamp solid when a trunk call rings in. If set to intercom prior-
ity (0), the Hotline key will not lamp for incoming trunk calls, but will lamp solid for intercom
calls.
➻ 15-02-10 : Multi-Line Telephone Basic Data Setup - Ringing Line Preference for Trunk
Calls
Use this option to select between Idle (0) and Ringing Line Preference (1) for trunk calls.
➻ 15-03-03 : Single Line Telephone Basic Data Setup - Terminal Type
Enter 1 for this option to allow a single line port to receive DTMF tones after the initial call
setup. Enter 0 to have the port ignore DTMF tones after the initial call setup. For Voice Mail,
always enter 1 (e.g., receive DTMF tones).
➻ 15-06-01 : Trunk Access Map for Extensions
Assign Trunk Access Maps to extensions.
➪ Aspire S: Trunk Access Maps 1-8
➪ Aspire: Trunk Access Maps 1-200