Filter
Top Products
Tie Lines
564 ◆ Features Aspire Software Manual
➻ 21-05-01 : Toll Restriction Class - International Call Restriction Table
21-05-02 : Toll Restriction Class - International Call Permit Table
21-05-04 : Toll Restriction Class - Maximum Number of Digits Table Assignments
21-05-05 : Toll Restriction Class - Common Permit Code Table
21-05-06 : Toll Restriction Class - Common Restrict Code Table
21-05-07 : Toll Restriction Class - Permit Code Table
21-05-08 : Toll Restriction Class - Restrict Code Table
21-05-09 : Toll Restriction Class - Restriction for Common Abbreviated Dialing
21-05-10 : Toll Restriction Class - Restriction for Group Abbreviated Dialing Numbers
21-05-11 : Toll Restriction Class - Intercom Call Restriction
21-05-12 : Toll Restriction Class - PBX Call Restriction
If Program 34-01-05 is set to “1”, define the toll restriction settings for tie lines.
➻ 21-05-13 : Toll Restriction Class - Restriction of Tie Line Calls
Enable (1) or disable (0) toll restriction for tie line calls (defined in Program 34-08-01).
➻ 22-02-01 : Incoming Call Trunk Setup
For each Night Service mode, enter service type 5 when the trunk should be a tie trunk.
➻ 34-01-01 : E&M Tie Line Basic Setup - DID/E&M Start Signaling
Enter 0 for 2nd dial tone, 1 for wink, 2 for immediate, or 3 for delay start signaling. To set out-
going signaling, refer to Program 14-02-01.
➻ 34-01-02 : E&M Tie Line Basic Setup - DID/E&M Start Signaling
Set the trunk signaling type to either dial pulse (0) or DTMF (1).
➻ 34-01-03 : E&M Tie Line Basic Setup - E&M Dial-In Mode
Determine if the incoming tie line call should be directed as an intercom call or if it should
follow the DID Translation Table in Program 22-11.
➻ 34-01-04 : E&M Tie Line Basic Setup - E&M Line Dial Tone
Enter 1 if the tie line should send dial tone to the calling system once the call is set up. Enter 0
if the tie line should not send dial tone.
➻ 34-01-05 : E&M Tie Line Basic Setup - System Toll Restriction
Enable (1) or disable (0) the ability for tie line calls to follow the system toll restriction entries
in Programs 21-05-01 through 21-05-13. If disabled, tie line toll restriction will be determined
by 21-05-13.
➻ 34-02-01 : E&M Tie Line Class of Service
Assign the tie line’s Class of Service (1-15). Use Program 20-14 to set the tie line Class of Service
options. You cannot use Programs 20-06 thru 20-17 to assign Class of Service to tie lines.
➻ 34-03-01 : Trunk Group Routing for E&M Tie Lines
Use this program to assign the trunk group route chosen when a user seizes a tie line and dials
9. Set Trunk Group Routing in program 14-06. If the system has ARS, dialing 9 accesses
ARS.
➪ Aspire Trunk Group Routes: 1-100
➻ 34-04-01 : E&M Tie Line Toll Restriction Class
If the system uses Toll Restriction, enter a Toll Restriction Class (1-15) for each tie line. The
system uses the class you enter in Program 21-05. You cannot use Program 21-04 to assign
Toll Restriction to tie lines.
➻ 34-05-01 : Tie Line Outgoing Call Restriction
This program lets you build a restriction matrix for trunk calls placed over a tie line. For each
tie line trunk group, enable (0) or disable (1) outgoing access to each CO trunk group.
➪ Aspire Trunk Groups: 1-100
➻ 34-06-01 : Add/Delete Digit for E&M Tie Line - Delete Digit
Some tie line networks pass the location number and extension number to the remote side. If
the system should ignore these digits, use this program to define the number of digits which
should be deleted (0-255, 255 deletes all digits) for a call.