Filter
Top Products
Paging, External
Aspire Software Manual Features ◆ 461
Programming
➻
10-03-01 : PCB Setup - Terminal Type (Circuit 1)
10-03-06 : PCB Setup - Terminal Type (Circuit 2)
When a 2PGDAD module is used for external page, type “6” should be assigned for the
2PGDAD circuit.
➻ 10-05-01 : General Purpose Relay Setup
Define which relay circuits (5-8) on the 2PGDAD Module are used for General Purpose
Relays. Also refer to Program 10-21-01 for the NTCPU relay assignments.
➻ 10-21-01 : NTCPU Hardware Setup - External Source Control Switch Selection
Specify the function of the relay switch for external tone source control (0=external MOH
source, 1=BGM source, 2=external speaker (Aspire only), 3=general purpose relay). If this
option is set to “2”, 803+1 will page and close the NTCPU relay. Upon hanging up, the relay
opens. If this option is set to “3”, 880+0 (Program 11-12-50) toggles the relay on and off.
➻ 11-12-50 : Service Code Setup (For Service Access)
Specify the service code to be used for toggling the relay open and closed (Default: 880).
➻ 15-07-01 : Programmable Function Keys
Assign function keys for External Paging zones (19 + zone) and External All Call Page (20). If
required, define a function key for a keyset to use the general purpose relay (50).
➻ 20-06-01 : Class of Service for Extensions
Assign a Class Of Service (1-15) to an extension.
➻ 20-13-29 : Class of Service Options (Supplementary Service) - Paging Display
In an extension’s Class of Service, enable (1) or disable (0) an extension’s ability to display
incoming internal paging information on their display.
➻ 31-01-02 : System Options for Internal/External Paging - Page Announcement Duration
Set the maximum allowable duration for a Paging announcement.
➻ 31-04-01 : External Paging Zone Group
Assign each External Paging Speaker to an External Paging Group (1-8) used for accessing the
zone. If zones 1-8 are not connected to PGDAD modules, set these unused zones to External Pag-
ing Group “0”.
➪ Aspire S External Paging Speaker/Zone: 1-8
➪ Aspire External Paging Speaker/Zone: 1-9
➻ 31-05-01 : Universal Night Answer/Ring Over Page
Assign Universal Night Answer ringing to each External Paging zone. For each trunk port,
you make a separate entry for each External Paging Speaker.
➪ Aspire S External Paging Speaker/Zone: 1-8
➪ Aspire External Paging Speaker/Zone: 1-9
➻ 31-06-01 : External Speaker Control - Broadcast Splash Tone Before Paging
Use this option to enabled or disable splash tone before Paging over an external zone. If
enabled (1=Splash, 2=Chime), the system broadcasts a splash tone before the External Paging
announcement.
➻ 31-06-02 : External Speaker Control - Broadcast Splash Tone After Paging
Use this option to enabled or disable splash tone after Paging over an external zone. If enabled
(1=Splash, 2=Chime), the system broadcasts a splash tone at the end of an External Paging
announcement.
➻ 31-06-04 : External Speaker Control - CODEC Transmit Gain Setup
31-06-05 : External Speaker Control - CODEC Receive Gain Setup
Select the CODEC gain types (1-32) for each External Page Speaker.
➪ Aspire S External Paging Speaker/Zone: 1-8
➪ Aspire External Paging Speaker/Zone: 1-9