Filter
Top Products
Single Line Telephones, Analog 500/2500 Sets
516 ◆ Features Aspire Software Manual
Default Setting
● Single Line Telephones function as soon as they are installed and properly programmed.
Programming
➻
10-03-01 : PCB Setup
Program all on-premise 500/2500 type single line telephones with circuit type ‘2’. Set the
DIOPU trunk to type ‘1’ when trunks should be defined for off-premise extension (OPX) use.
➻ 10-03-03 : PCB Setup, For SLIU Unit - Transmit CODEC Gain Type
10-03-04 : PCB Setup, For SLIU Unit - Receive CODEC Gain Type
Assign transmit and receive levels for 500/2500 type single line telephones.
➻ 10-09-01 : DTMF and Dial Tone Circuit Setup
If the system has 2500 type (DTMF) single line extensions, allocate at least one circuit for
analog extension DTMF reception (entry 0 or 1).
● Use the following as a guide when allocating DTMF receivers:
- In light traffic sites, allocate one DTMF receiver for every 10 devices that use them.
- In heavy traffic sites, allocate one DTMF receiver for every five devices that use them.
➻ 15-03-01 : Single Line Telephone Basic Data Setup - SLT Signaling Type
Enter 0 if single line phone is a 500 type (dial pulse). Enter 1 if single line telephone is a 2500
type (DTMF).
➻ 15-03-03 : Single Line Telephone Basic Data Setup - Terminal Type
Enter 0 for normal 500/2500 type telephones. Enter 1 if a Voice Mail port (refer to “Voice
Mail” for more).
➻ 20-03-02 : System Options for Single Line Telephones - Ignore Received DP Dial on
DTMF SLT Port
Use this option to define whether the system should receive dial pulse and DTMF signals (0)
or ignore dial pulse and only accept DTMF signals (1).
➻ 20-06-01 : Class of Service for Extensions
Assign a unique Class of Service for Dual OPX phones only when using Continued Dialing.
➻ 20-13-13 : Class of Service Options (Supplementary Service) - Continued Dialing
Set option to ‘0’ to prevent dual DTMF tones when using Continued Dialing.
➻ 20-15-01 : Ring Cycle Setup - Normal Incoming Call on Trunk
Define the ringing cycle (1-13) for normal incoming trunk calls (DIL, ring group, etc.).
➻ 20-15-03 : Ring Cycle Setup - Incoming Internal Calls
Define the ringing cycle (1-13) for ICM calls.
➻ 20-15-05 : Ring Cycle Setup - DID
Define the ringing cycle (1-13) for DID calls.
➻ 80-03-01 : DTMF Tone Receiver Setup
80-04-01 : Call Progress Tone Detector Setup
If required, modify the criteria for dial tone detection and call progress tone detection for the
DTMF tones received at a single line telephone.
➻ 82-04-01 - 82-04-14 : SLIU Initial Data Setup
Set various timing parameters for the analog station PCBs. The entries you make in this pro-
gram affect all SLIU PCBs installed (make time, break time, hookflash, etc.).
➻ 82-07-01 : CODEC Filter Setup for Analog Station Ports
Define the CODEC (QSLAC) Filter (0 = No filter, 1 = 0dB Loss, 2 = 4dB Loss, 3 = 8dB Loss,
4 = Specified Data from Program 82-09) for each analog extension port
➪ Aspire S Analog Ports: 1-18
➪ Aspire Analog Ports: 1-256