Filter
Top Products
Intercom
Aspire Software Manual Features ◆ 367
➻ 20-08-01 : Class of Service Options (Outgoing Call Service) - Intercom Calls
In an extension’s Class of Service, enable (1) or disable (0) an extension’s ability to place
Intercom calls.
➻ 20-08-11 : Class of Service Options (Outgoing Call Service) - Protect ICM Call Mode
Switching by Caller
When an extension is set to ring mode for ICM calls, enabling this option prevents callers
from changing the call to voice announce mode (disable=0, enable=1).
➻ 20-11-07 : Class of Service Options (Hold/Transfer Service) - Transfer Without Holding
In an extension’s Class of Service, enable (1) or disable (0) an extension’s ability to Transfer a
call without holding. If the Busy Status Display feature is to be used, this option should be set
to “0”.
➻ 20-13-22 : Class of Service Options (Supplementary Service) - Busy Status Display
In an extension’s Class of Service, enable (1) or disable (0) an extension’s ability to use the
Busy Status Display feature.
➻ 20-17-01 : Operator’s Extension
Assign the operator’s extension.
➻ 20-18-01 : Service Tone Timer - Extension Dial Tone Time
Set the Extension Dial Tone Time (0-64800 seconds). After getting Intercom dial tone, a key-
set user has this interval to dial the first digit of the Intercom call.
➻ 21-01-02 : System Options for Outgoing Calls - Intercom Interdigit Time
Set the Intercom Interdigit Time (0-64800 seconds). When placing Intercom calls, users must
dial each digit within this interval.
➻ 82-01-01 : Incoming Ring Tone - Intercom Ring Tone
Customize the Intercom ring tone.
For Handsfree Answerback/Forced Intercom Ringing . . .
➻ 20-02-12 : System Options for Multi-Line Telephones - Forced Intercom Ringing
Determine if an extension’s ICM calls should be set as Forced Intercom Ringing (1). If dis-
abled (0), Intercom calls voice-announce. For all NEC Cordless phones (P/N 730082), this
option must be set to “1” as voice announce is not possible.
➻ 20-06-01 : Class of Service for Extensions
Assign a Class Of Service (1-15) to an extension.
➻ 20-08-10 : Class of Service Options (Outgoing Call Service) - Switching from Handsfree
Answerback to Forced Intercom Ringing
In an extension’s Class of Service, enable (1) or disable (0) an extension’s ability to toggle
between Handsfree Answerback and Forced Intercom Ringing for outgoing Intercom calls
(dial 1 or Service Code 812).
➻ 20-09-05 : Class of Service Options (Incoming Call Service) - Setting Handsfree Answer-
back/Forced Intercom Ringing
In an extension’s Class of Service, enable (1) or disable (0) an extension’s ability to set
Handsfree Answerback (Service Code 821) and Forced Intercom Ringing (Service Code 823)
for incoming Intercom calls.
➻ 20-13-06 : Class of Service Options (Supplementary Service) - Automatic Off Hook Signaling
In an extension’s Class of Service, enable (1) or disable (0) the extension’s ability to automat-
ically send Off Hook Signals while busy on a handset call. Setting this option to “0” will pre-
vent Intercom calls from ringing the CALL2 key - instead the caller will hear a busy signal.
➻ 80-01-01 : Service Tone Setup - Tone 28, Speaker Monitor Tone
This tone changes the tone the originator of an ICM call hears. (The tone cannot be changed
for what is heard by the user when receiving an ICM call.)