Filter
Top Products
Central Office Calls, Placing
Aspire Software Manual Features ◆ 221
➻ 20-02-09 : System Options for Multi-Line Telephones - Disconnect Supervision
Enable (1) disconnect supervision for the system.
➻ 20-06-01 : Class of Service for Extensions
Assign a Class Of Service (1-15) to extensions.
➻ 20-07-12 : Class of Service Options (Administrator Level) - Trunk Port Disable
For each Class of Service (1-15), enable (1) or disable (0) an extension’s ability to use the
Trunk Port Disable feature.
➻ 20-08-02 : Class of Service Options (Outgoing Call Service) - Trunk Calls
In an extension’s Class of Service, enable (1) or disable (0) trunk calling.
➻ 20-13-13 : Class of Service Options (Supplementary Service) - Continued Dialing
In an extension’s Class of Service, enable (1) or disable (0) an extension’s ability to use Con-
tinued Dialing which allows DTMF signal sending while talking on extension.
➻ 21-01-03 : System Options for Outgoing Calls - Trunk Interdigit Time (External)
The system waits for this timer to expire before placing the call in a talk state (Call Timer
starts after timer expires, Voice Over and Barge-In are not allowed until after timer expires). If
set to “0”, Voice Over and Barge In will not work for external calls. This timer affects CO and
PRI outdialing. (0-64800 Seconds)
➻ 21-01-15 : System Options for Outgoing Calls - Outgoing Disable on Incoming Line
Enable (1) or disable (0) the Outgoing Disable on Incoming Line feature.
➻ 21-01-16 : System Options for Outgoing Calls - Supervise Dial Detection Timer
With the Outgoing Disable on Incoming Line feature, if dial tone is not detected after the
extension answers an incoming line, the system determines the call is unable to complete and
releases the DTMF receiver (0-64800 Seconds).
➻ 21-01-17 : System Options for Outgoing Calls - Restriction Digit in Outgoing Disable on
Incoming Line
With the Outgoing Disable on Incoming Line feature, determine the number of digits (0-9) to
be dialed before the call should be disconnected.
➻ 21-02-01 : Trunk Group Routing for Extensions
Assign Program 14-06 routes to extensions.
➪ Aspire S: Trunk Group Routes 1-8
➪ Aspire: Trunk Group Routes 1-100
➻ 21-15-01 : Alternate Trunk Route for Extensions
Designate the trunk route accessed when a user dials the Alternate Trunk Route Access Code.
Refer to “Trunk Group Routing” to set up outbound routing.
➪ Aspire S: Trunk Group Routes 1-8
➪ Aspire: Trunk Group Routes 1-100
➻ 24-02-07 : System Options for Transfer - Forced Release for Trunk-to-Trunk Transfer
This timer will start when a trunk begins talking with another trunk (for example: trunk-to-
trunk transfer, outgoing from trunk, Tandem Trunking) (0-64800).
➻ 81-01-01 : Analog Trunk Data Setup
Review the Analog Trunk Timers for compatibility with the connected telco.
➻ 81-09-01 : COIU CODEC Filter Data Setup
The system will use the settings in this program when Program 81-07-01 : CODEC Filter
Setup for Analog Trunk Ports is set to "4 - Specified Data". These values should not be
changed from their default settings unless directed by NEC’S Technical Service department.
The side tone of the COIU is adjusted using all 16 values, however, special software is
required in order to compute these values. The setting is not proportional to the gain level. To
change these values, contact NEC’s Technical Service department for assistance.
➻ 82-08-01 : Sidetone Volume Setup
Use this program to adjust of the keyset side tone volume. There are two levels, based on
whether the connected trunk is a digital trunk or analog trunk.