Filter
Top Products
Transfer
590 ◆ Features Aspire Software Manual
➻ 20-11-07 : Class of Service Options (Hold/Transfer Service) - Transfer Without Holding
In an extension’s Class of Service, enable (1) or disable (0) the extension’s ability to use
Transfer Without Holding.
➻ 20-11-08 : Class of Service Options (Hold/Transfer Service) - Transfer Display
In an extension’s Class of Service, enable (1) or disable (0) the extension’s incoming Transfer
pre-answer display.
➻ 20-11-11 : Class of Service Options (Hold/Transfer Service) - Automatic On Hook Transfer
In an extension’s Class of Service, enable (1) or disable (0) the extension’s ability to use Auto-
matic On Hook Transfer. If enabled, user must press HOLD and dial the extension number to
Transfer the call. If disabled, a user must have a Transfer Programmable Function Key. To
transfer the call, the user would press HOLD, dial the extension number, then press the Trans-
fer Programmable Function key to complete the transfer.
➻ 20-11-18 : Class of Service Options (Hold/Transfer Service) - Transfer Recall On Receiving
COS
Allow (0) or deny (1) unanswered Transferred calls to the COS from recalling the originating
extension.
For example, with this option set to ‘1’ for COS 1, calls transferred by any COS to any
extension with a COS of 1, will not recall.
➻ 20-11-20 : Class of Service Options (Hold/Transfer Service) - Transfer Recall On
Originating COS
Allow (0) or deny (1) unanswered Transferred calls from the COS from recalling the originat-
ing extension.
For example, with this option set to ‘1’ for COS 1, any call transferred by an extension
with COS 1, will not recall.
➻ 20-13-10 : Class of Service Options (Supplementary Service) - Barge In Mode
In an extension’s Class of Service, enable the Barge In Speech Mode (0) at the initiating
extension (i.e., Barge In initiator). This is required in order to transfer a call into a conference.
➻ 20-13-15 : Class of Service Options (Supplementary Service) - Barge In Initiate
In an extension’s COS, enable (1) or disable (0) the extension’s ability to Barge In to a call.
➻ 20-13-16 : Class of Service Options (Supplementary Service) - Barge In Receive
In an extension’s COS, enable (1) or disable (0) the extension’s ability to receive a Barge In on
a call.
➻ 20-13-17 : Class of Service Options (Supplementary Service) - Barge In Tone/Display
Enable (1) or disable (0) the Barge In Tone. If disabled, this also turns off the Barge In display
at the called extension. As this option is for extensions and trunks don’t have an option for a
Barge In Tone, the tone will be sent to the trunks based on the Class of Service of the transfer-
ring extension.
➻ 20-13-32 : Class of Service Options (Supplementary Service) - Multiple Barge In
Enable (1) or disable (0) the extension’s ability to have multiple user’s Barge In to their con-
versation.
➻ 20-14-11 : Class of Service Options For DISA/E&M - DISA/Tie Trunk Barge In
Determine if DISA and tie trunk users should have the ability to dial a service code to Barge
In to a Conference call (0=disabled, 1=enabled).
➻ 20-15-09 : Ring Cycle Setup - Callbacck/Transfer Ring
Define the ringing cycle for transferred and callbacks (ringing cycle 1-13).
➻ 20-18-07 : Service Tone Timer - Intrusion Tone Repeat Time
After a user Barges In, the system repeats the Barge In tone after this interval. Normally, you
should disable this timer by entering 0. (This timer also affect any other types of call interrup-
tion features, such as Voice Mail Conversation Recording, Voice Over, etc.)